• TL081: Loop stability

  

  Zoey Wu

  TI Thinks Resolved

  Part Number: TL081 Hi team, Could u help to tell me that will the added capacitors(C2&C1) influence the loop stability of the system as attached?

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• TL081H: Output stage difference from legacy TL081

  

  Alex Pogossov

  Resolved

  Part Number: TL081H Other Parts Discussed in Thread: TL081 , TL084H , TL084 Hello, From datasheet SLOS081M is appears that output swing, especially positive for the new TL081H is close to the rail (500mV). Old TL081 can go only 1.5V from the rails. However…

  • Resolved

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• RE: TL783: PWM Based Regulator Design

  

  Fatih Cavdarci

  Resolved

  Hi Alex, I am sharing the schematic below. I used LM324 as opamp. I can not adjust the output value with single supply opamp, but when I connect the TL081 with dual supply I can do it. Voltage output value must be normally ~60V when settting the pwm-anaog…

  • 2 months ago
  • Power management
  • Power management forum

• TL081: Input Impedance

  

  Mark Philip Felipe

  TI Thinks Resolved

  Part Number: TL081 Hi Team, we have a customer that would like to ask the input capacitance value of TL081CP. He also wants to confirm if he could leave the offset pin floating. We hope you could help us. Thank you. -Mark

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• TL081: About the phase of signal in inverting and non-inverting

  

  user6163394

  Resolved

  Part Number: TL081 I simulate the current sensing circuit by TINA. When the signal is inverting input, I can see a 90 degree phase shift in IN+ and IN-. Why?

  • Resolved

  • over 5 years ago
  • Amplifiers
  • Amplifiers forum

• TL081: TL081 REPLACEMENT

  

  user5102208

  TI Thinks Resolved

  Part Number: TL081 Other Parts Discussed in Thread: TLE2071A-Q1 , OPA196 Hi all, Could you help me find one good part for TL081 replacement. I want one which is similar to TL081 in function, but Operating Temperature Range can reach -40~125℃！ Thank a lot…

  • over 6 years ago
  • Amplifiers
  • Amplifiers forum

• TL081A: Amplifier

  

  Abhishek Kumar

  TI Thinks Resolved

  Part Number: TL081A Other Parts Discussed in Thread: TL081 , TLV9052 , TLV9051 , Tool/software: I am using TL081 op- amp for voltage sensing. But, at some voltage level I can see that the output voltage of the op- amp is taking a dip to half the voltage…

  • 10 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• WEBENCH® Tools/TL081: cant find the netlist

  

  zhenchao tang

  Resolved

  Part Number: TL081 Tool/software: WEBENCH® Design Tools I cannot find the a Netlist as a *.CIR or *.LIB or .MOD File , Where can I find this file ? thank

  • Resolved

  • over 6 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• RE: TINA/Spice/TL081: Eagle Simulation Problems

  

  Jonathan Hillengas

  Resolved

  I saw that you were able to figure out how to make this TL081 device simulate. and I was wondering how you did so because I having trouble simulating it in eagle as well?

  • over 7 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum
Answered

• TINA/Spice/TL081: offset pins are missing

  

  user4969388

  Resolved

  Part Number: TL081 Other Parts Discussed in Thread: TINA-TI , , TL082 Tool/software: TINA-TI or Spice Models Hello, I've found a serious problem. I've tried to used the TL081 Amplifier with offset, but the Spice was not well definied. Please catch…

  • Resolved

  • over 8 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

Didn't find what you are looking for? Post a new question.