• TLC556: TLC556

  

  ROBERT BISHOP

  Part Number: TLC556 Other Parts Discussed in Thread: NA555 , , TPL5110 , LM339 , TLV4082 , TPL5111 Tool/software: Desired function waveform.pdf NA555, NE555, SA555, SE555 Precision Timers (Rev. I).pdf Hello I forgot to include some information…

  • 3 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• TLC556: TLC556 Astable operation

  

  Nicholas Yunker

  Resolved

  Part Number: TLC556 Other Parts Discussed in Thread: NE555 , CD4069UB I am attempting to setup the TLC556 duel timer to control both frequency and Pulse Width of the output frequency. I have set up the first stage in Astable operation to generate a period…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• TLC556: Trigger Astable operation to restart

  

  Nicholas Yunker

  Part Number: TLC556 Hello, I am using a TLC556 duel timer to create a stable time period with the first timer and to use that to trigger the second timer in mono-stable mode to generate a pulse based on a potentiometer input and the timer period generated…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• TLC556: Minimum TRIG Pulse Width in Monostable Configuration

  

  BrainX Solution

  TI Thinks Resolved

  Part Number: TLC556 Other Parts Discussed in Thread: LMC555 , TLC555 Dear TI E2E Support Team, Our current project involves implementing the TLC556 dual CMOS timers IC. Specifically, we've encountered an issue with one of the timers configured as…

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

• TLC556: TLC556ID design help

  

  Zhonghui Xu

  TI Thinks Resolved

  Part Number: TLC556 Hi team, How the timer chip realize that the output pin exports high level for 10 seconds and low level for 50 seconds. And would you tell me how to set the resistors and capacitors value if the chip is capable to do so. Best…

  • over 4 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• TLC556: Does the TRIG input have protection diodes? If so, what is the maximum allowed input current?

  

  Mike Andrews

  Resolved

  Part Number: TLC556 Hi, I actually used a TLC556 in a new design. Never thought I'd have the chance again. Go figure. :-) Because the TRIG input is edge-sensitive I used the one-shot output of the first-half of the dual-timer to generate an RC pulse…

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• TLC556: Unused pins

  

  Elisha Tarroza71

  Resolved

  Part Number: TLC556 Other Parts Discussed in Thread: TLC555 Hello, Datasheet mentions that unused input pins should be connected to "appropriate" logic levels. May I know if these are the voltages at the electrical characteristics? Since there are varying…

  • Resolved

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum

• TLC556: TLC556MD

  

  Norm Donkersloot

  Part Number: TLC556 Hello, We have a design which uses the TLC556 dual timer on a circuit board. While investigating solderability issues with surface mount test points where x-rays of the test points were taken, the question came up on whether the…

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

• TLC556: Control of B from A

  

  Erik Persson

  Part Number: TLC556 Would like to switch astable 556B on/off by one shot 556A. Low speeds. Regards, Erik <email address removed>

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

• TLC556: Temperature drift of External cap

  

  Shunsuke Nagata

  TI Thinks Resolved

  Part Number: TLC556 Hi, I would like to know the selection for the external CAP. The capacitor value will be shifted depend on ambient temperature. Is there recommendation accuracy if I use calculation in datasheet? (Should I select +/-10%CAP depending…

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.