Search tips
Showing 47 results View by: Thread Post Sort by

  • TLV2372-Q1: TLV2372 Multivibrator abnormal operation

    TI Thinks Resolved
    Part Number: TLV2372-Q1 Dear TI community. I have questions about multibrator behavior. Multibrator was used for EV battery voltage measurements. The attached file is a circuit diagram and a measurement waveform. If only 12V low voltage is connected…
    • Answered

  • TLV2372: IDGKR

    Resolved
    Part Number: TLV2372 Hello, could you please help to find documentation on TLV2372IGKR with information about marking on TOP and Back side of component, and also decoder of label on reel for same position? Thank you in advance
    • Resolved
    • Answered

  • TLV2372: How to step down the output voltage of the filter to 0 to 3V from 0 to 10V keeping same cut off frequency (60KHz) at -3dB and order (3rd order Butterworth filter)?

    Resolved
    Part Number: TLV2372 Hi, The input to the circuit given below is a sine wave with amplitude 5V (0V to 10V) and frequency 1.4k Hz. It is a 3rd order Butterworth filter with cut off frequency of 60KHz at -3dB Here I am getting the output of 5V …
    • Resolved

  • TLV2372: Input over voltage stress

    TI Thinks Resolved
    Part Number: TLV2372 Hi team My customer wants to know how it in failure if the TLV2372 is gave the over voltage stress. Please let me know if you have the FMEA. Best regards. Hayashi
    • Answered

  • TLV2372： if really need small capacitor and resistor or not

    Resolved
    Part Number: TLV2372 Hi， Now use TLV2372(VDD=12V)to enlarge high level voltage of pwm from 3.3V to about 10.7V ，frequency range：1K--25KHZ 1.Is it necessary to connect a small capacitor in parallel with R1? if really need capacitor ,how much calculate…
    • Resolved

  • TLV2372: Input Bias Current/offset current

    TI Thinks Resolved
    Part Number: TLV2372 Hi team, The datasheet mentions that TLV2372's Input bias current/offset current is as below. But the test condition is VIC=VDD/2. I want to understand when VIC is changed in 0~VDD level, will input bias current/offset current…
    • Answered

  • TLV2372-Q1: Requesting Electrical Characteristics

    Resolved
    Part Number: TLV2372-Q1 Team, Could you please help by providing the following electrical characteristics for TLV2372QDRQ1: Maximum Storage Temperature (°C) Minimum Storage Temperature (°C) Input Voltage (either terminal) Common-mode input…
    • Resolved

  • RE: TINA/Spice/TLV2372: Bode Gain Plot in actual magnitude instead of dB

    Jared, What's shown is in fact the absolute value rather than Vout/Vin. However, in TINA Vin is fixed to 1 in AC sim. A workaround is to insert a VCVS to convert Vin to the actual input. E.g. if your input signal swings 1mV, you will set the VCVS…
    • Answered

  • RE: TINA/Spice/TLV2372: Schmitt Trigger Oscillator

    Resolved
    Mike Here is 40Hz 30% oscillator. TLV2372 Schmitt Trigger Oscillator.TSC

  • TLV2372 power supply unbalance

    Other Parts Discussed in Thread: TLV2372 Hi all, TLV2372 is powered with +5V and -5V power rails. Card is inserted in a rack and it could be the case someone extract the card without removing power. The +5V rail switches off quicker than -5V one,…

Didn't find what you are looking for? Post a new question.