Search tips
Showing 18 results View by: Thread Post Sort by

  • TLV3541: Cross for ADA4891-1ARJZ

    Part Number: TLV3541 Other Parts Discussed in Thread: LMH6611 Hi, Customer of mine is looking for a cross for ADA4891-1ARJZ. I recommended the TLV3541, but they said it is too large (and in fact, so is the ADA4891-1ARJZ part they use today). Can you recommend…

  • TLV3541: Wien Bridge oscillator

    Part Number: TLV3541 Other Parts Discussed in Thread: TINA-TI , , OPA863 , OPA810 Hi Team, I'm looking for oscillator solution that meets following requirement. Vdd: 5V freq: 400kHz ~ 1MHz (no adjustable requirement) Vout_pp: 3~5V low distortion. I created…
    • Answered

  • TLV3541: TLV3541

    Resolved
    Part Number: TLV3541 Other Parts Discussed in Thread: SN10501 , LMH6654 Hello, I'm looking for an OP-AMP like the TLV3541, but with a higher supply voltage than 5.5 V. The OP-AMP should have the following features: 12V supply voltage GBP>=100 MH…
    • Resolved

  • TLV3541: PSpice Model for TLV354x doesn't work

    TI Thinks Resolved
    Part Number: TLV3541 Other Parts Discussed in Thread: TINA-TI Hi, I use TLV354x PSpice Model (Rev. A) SBOMA83A.ZIP (13 KB) - PSpice Model in Cadence Orcad 17.2. If I simulate TLV354 Test Circuit.opj, it runs. If I change the power supply to non-symmetric…

  • RE: OPA2387: Interfacing OPAx387 with with Acoustic emission Sensor VS45-H

    Hari, LMH6514SQ isn't a bad choice ; the care about is the 200 ohm input impedance. The preamp should be quite low noise and if needed a buffer could be added to interface preamp to LMH amp TLV3541 could be a good preamp that can drive 200 ohm load…

  • TLV3541: Voltage follwer for Active shield

    Part Number: TLV3541 Dear Enginner, Hi, I am going to use TLV3541 to create a voltage follower. Because I want to apply Active shield (AC shield) in capacitive sensing. Our sensor signal is duplicated by a voltage follower and the duplicated sinal by the…

  • TLV3541: I can't simulate TLV3541 with P-SPICE.

    TI Thinks Resolved
    Part Number: TLV3541 I downloaded the TLV3541 spice model from the homepage and simulate to P-SPICE. However, the following error occurred and simulation was not possible. ERROR(ORPSIM-15108): Subcircuit VCCS_EXT_LIM used by X_U16.XVCM_CLAMP is…

  • TLV3541: AD8615AUJZ-R2 Replacement Availability

    TI Thinks Resolved
    Part Number: TLV3541 hi I am trying to replace the AD8615AUJZ-R2 with TLV3541IDBVR. We will contact you as an alternative part. (1.8V 115mA_max, 3.3V 95mA_max, 5V 50mA_max variable power rail will be used.) The current specification can be lowered slightly…

  • TLV3541: will use on 120mA

    Part Number: TLV3541 Hi Sirs, Sorry to bother you. We have use TLV3541 on smart card application. We found if load around 120mA, the voltage will drop. We need survey solution that could keep voltage when load 120mA. Does TI have others solution can share…

  • RE: LM7171: LM7171 can it be used with a single-supply?

    You could think about using the TLV3541, or a similar RRIO-HF-OPAmp, in combination with the LM7705: joel_tlv354.TSC Kai

Didn't find what you are looking for? Post a new question.