• TPL5110-Q1: Tpl5110

  

  Allan Balgley

  TI Thinks Resolved

  Part Number: TPL5110-Q1 Other Parts Discussed in Thread: TPL5110 Tool/software: Hello, I am looking to use the TPL5110 chip. I am not using a microcontroller in my circuit. I am currently using the LMC555CTP but in is draining a cr2032 3v 220mah battery…

  • 1 month ago
  • Clock & timing
  • Clock & timing forum

• TPL5110-Q1: TPL5110

  

  Allan Balgley

  TI Thinks Resolved

  Part Number: TPL5110-Q1 Other Parts Discussed in Thread: TPL5110 Tool/software: Hello, I am looking to use the TPL5110 chip. I am not using a microcontroller in my circuit. I am currently using the LMC555CTP but in is draining a cr2032 3v 220mah battery…

  • 1 month ago
  • Clock & timing
  • Clock & timing forum
Answered

• TPL5110-Q1: TPL5110-Q1

  

  Allan Balgley

  Resolved

  Part Number: TPL5110-Q1 Tool/software: How to design a done signal without using a microcontroller in the circuit

  • Resolved

  • 1 month ago
  • Clock & timing
  • Clock & timing forum
Answered

• TPL5110: TPL5110 Control DELAY/M_DRV by two ways

  

  _Unknown_

  Resolved

  Part Number: TPL5110 Tool/software: May I control DELAY/M_DRV pin (pin 3) by two ways (manual switch or signal)? If I can do it, how I need to design the circuit? I want to control it by two ways as shown below to turn on the P-MOS. 1. Manual switch 2…

  • Resolved

  • 2 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• TPL5110-Q1: Power down after 8 seconds with no input

  

  Ron Michallick

  Resolved

  Part Number: TPL5110-Q1 Other Parts Discussed in Thread: TPL5110 Tool/software: Power down after 8 seconds with no input (reset back to 0 sec on retrigger). Important for low current draw when off. Power up on next input. Can any TPL5xxx help with this…

  • Resolved

  • 1 month ago
  • Clock & timing
  • Clock & timing forum
Answered

• TPL5110: Current draw with M_DRV high during and after POR

  

  Marcel Wilke

  Resolved

  Part Number: TPL5110 Tool/software: Hi Ti, I did a design with the Nano Power Timer TPL5110. The device works as expected but I am facing one issue which is not mentioned in the datasheet. For my circuit and application i need to hold M-DRV high during…

  • Resolved

  • 1 month ago
  • Clock & timing
  • Clock & timing forum
Answered

• TPL5110-Q1: One shot mode just using M_DRV signal

  

  FY AY

  Resolved

  Part Number: TPL5110-Q1 Tool/software: Hi TI Team, https://e2e.ti.com/support/clock-timing-group/clock-and-timing/f/clock-timing-forum/912946/tpl5110-q1-one-shot-mode-without-done-signal/3374428?focus=true According to this post, I can use like this…

  • Resolved

  • 1 month ago
  • Clock & timing
  • Clock & timing forum
Answered

• TPL5110: 24 hour timer

  

  Kei Kuwahara

  Resolved

  Part Number: TPL5110 Tool/software: Hello team, My customer would like to configure 24 hour timer. (Delay time is 24 hours) They want to wake up the MCU every 24 hours. Is there any way we can configure this device or another timer IC to configure 24hour…

  • Resolved

  • 3 months ago
  • Clock & timing
  • Clock & timing forum

• TPL5110: I am stuck at TPL5110 timer holding pulse .

  

  Bishal Naya

  TI Thinks Resolved

  Part Number: TPL5110 I am stuck at TPL5110 output voltage holding. It just gives me a small 0.5uS pulse on Output line. i need minimum 1 second pulse on output line to trigger my circuit. Can anybody help me out. T

  • 10 months ago
  • Clock & timing
  • Clock & timing forum

• TPL5110-Q1: about Timer accuracy: 1% (typical) issue

  

  Lawrence He

  TI Thinks Resolved

  Part Number: TPL5110-Q1 Other Parts Discussed in Thread: BQ32000 , BQ32002 Hi, Support Team do we have different temperature about timer accuracy ppm? (-40 to 85 deg), (85 to 105 deg),(105 to 125 deg) if any suggestion, Please advise me. Thanks, Best regards…

  • 8 months ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.