Search tips
Showing 11 results View by: Thread Post Sort by

  • TS5A23167: TS5A23167 Maximum Analog Voltage

    Answer Suggested
    Part Number: TS5A23167 Tool/software: The data sheet indicates a maximum supply voltage of 6.5V, and analog voltage of +0.5V over V supply. And note 4 indicates that the input voltage limits can be exceeded if the clamp current ratings are observed…
    • Answered

  • TS5A23167: about data sheet

    Resolved
    Part Number: TS5A23167 Other Parts Discussed in Thread: TS5A23166 , Tool/software: Hi all, We are examining the specifications for both TS5A23166 and TS5A23167. TS5A23166: NO→COM (IN is high active ON) NO is normally open and open when the power is…
    • Resolved

  • TS5A23167: When no VIN

    TI Thinks Resolved
    Part Number: TS5A23167 Hi, When TS5A23167 V+ pin is low, no power supply, What is the NC1 and COM1 status? Is it will normaly closed?(short to each others) Thanks! Jeff

  • TS5A23167: Antenna Switching

    TI Thinks Resolved
    Part Number: TS5A23167 Other Parts Discussed in Thread: SN74CBTLV3126 , TMUX121 Hi, I have connected 2 125KHz antennas to the switch TS5A23167 through which it is connected to the 125KHz reader, am using TS5A23167 to switch 125KHz antenna. The Reader…
    • Answered

  • TS5A23167: TS5A23167YZPR

    Resolved
    Part Number: TS5A23167 Hi, I don't see a Tpd (propagation delay) information in a data sheet. Please, assist to get. Youry
    • Resolved

  • TS5A23167: Connection when unpowered & data sheet mismatch

    TI Thinks Resolved
    Part Number: TS5A23167 Hi, 1. TS5A23167 is powered off but COM2 (pin #C2) is 3V as connected a battery on board. According to the spec- Vi/o < V+ I know that it has Isolation in Powered-Off Mode but Is it OK? No damage in long term? 2. Mismatch…
    • Answered

  • TS5A23167: BGA package pin nomenclature

    Resolved
    Part Number: TS5A23167 Hello, I have a customer using P/N TS5A23167YZPR (DSBGA package), BGA package shown pin is A1, B1, C1, D1, A2, B2, C2, D2. But Datasheet shown Pin 1, 2, 3, 4, 5, 6, 7, 8. The footprint and symbol shows A1, B1, … Could you…
    • Resolved

  • MUX507: Inquiry regarding MUX507IPWR: I2C Bus Voltage Drop in Multi-Board Systems during Partial Power-Off

    Answer Suggested
    Part Number: MUX507 Other Parts Discussed in Thread: TS3A5017 , TS5A23167 , TS5A3167 Hi Support Team, We have a storage project utilizing the MUX507IPWR as an I2C MUX, with the circuit configuration as shown in the attached schematic. In our application…

  • TMUX1121: When no Vin

    TI Thinks Resolved
    Part Number: TMUX1121 Other Parts Discussed in Thread: TS5A23167 Hi, When TMUX1121 VDD pin is low, no power supply, What is the S1 and D1 status? Is it will normaly closed?(short to each others) Thanks! Jeff

  • RE: INA220: SDA pull-up voltage drop

    The absolute maximum ratings forbid voltages above V S + 0.3 V on the SCL pin. (Apparently, that table confuses the SCL and SDA pins.) To disconnect the I²C line(s), use an always-on switch with powered-off protection like the TS5A3167/TS5A23167.

Didn't find what you are looking for? Post a new question.