Answered

• TXB0104-Q1: Over-Voltage on Inputs

  

  Jessica Riley

  Resolved

  Part Number: TXB0104-Q1 Tool/software: Hello, I am trying to determine what will happen when the inputs or outputs on one side of the TXB0104-Q1 are subjected to over-voltage (up to 36V). I do not expect the part to remain undamaged, but I would like…

  • Resolved

  • 2 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: It was connecting to bootstrp pin and need to know it bootstrap level?

  

  Alpha Ting

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Other Parts Discussed in Thread: TXU0204-Q1 , TLV840-Q1 Tool/software: Hi sir The TXB0104-Q1 is connecting between SOC bootstrap pin and usb-to-uart bridge(FT230XQ-R). The bootstrp pin side (point B) has pull low resistor 47Kohm…

  • 1 month ago
  • Logic
  • Logic forum

• TXB0104-Q1: Package Inquiry

  

  Evan Wang

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Tool/software: Hi TI Expert, Quite confused about the package info of the TXB0104QRUTRQ1 . Does that means we extend the pad to the package side like wettable flank? Like we have conductive pad on each side so it's easier for checking…

  • 2 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: Abnormal start-up translation waveform

  

  Jiahao Yu

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Other Parts Discussed in Thread: TXU0104-Q1 , TXB0104 Tool/software: Hi Expert, My customer Li-Auto is using this device for level shifting between MCU and SoC in IVI platform. Below is the simplified diagram and schematic: (BTB…

  • 2 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: TXB0104QRUTRQ1-Failure Mode Request

  

  Silambarasan D

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Tool/software: Hi Ti Team, Please provide below mentioned part numbers Failure modes details. 1. TXB0104QRUTRQ1 Thanks Regards, Silambarasan

  • 3 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: Impact of Delayed Powering of VCCA on Device Functionality

  

  VISHNU AG

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Tool/software: In our application, VCCA will only be powered ON after VCCB has been powered on. Will this cause any functional impact, such as device failure

  • 3 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: Functional Impact of VCCB Absence with Constant VCCA on Chip

  

  VISHNU AG

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Tool/software: We have a situation where VCCA will always be present and VCCB will not be. In that situation, will there be any functional impact on the chip, such as device damage?

  • 3 months ago
  • Logic
  • Logic forum
Answered

• TXB0104-Q1: Output Load Considerations

  

  shihui xu

  Resolved

  Part Number: TXB0104-Q1 Tool/software: chapter 8.3.3 Output Load Considerations says : " PCB signal trace-lengths should be kept short enough such that the round trip delay of any reflection is less than the one-shot duration. This improves signal…

  • Resolved

  • 4 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: The reliability of IC after running it out of specification for a while

  

  Mehmet Bulent Havur

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Other Parts Discussed in Thread: TXB0104 Tool/software: Hello, I am using TXB0104-Q1, a 4-bit bidirectional voltage-level translator with auto direction sensing and +/-15kV ESD IC with the given schematic as below: We have the…

  • 3 months ago
  • Logic
  • Logic forum

• TXB0104-Q1: TXB0104-Q1 one-shot doesn't work during power-up

  

  Ted Xu

  TI Thinks Resolved

  Part Number: TXB0104-Q1 Other Parts Discussed in Thread: TXB0104 , TXU0304-Q1 , TIDA-00296 Hi BU team My customer reported txb0104-Q1 didn't always output any waveform after powered-up. The schematic is shown in below screenshot. The DSP send 12.28MHz…

  • 8 months ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.