Search tips
Showing 312 results View by: Thread Post Sort by

  • XTR111: Voltage Output Information

    TI Thinks Resolved
    Part Number: XTR111 Other Parts Discussed in Thread: XTR300 , XTR305 Hi, I'm looking for some information on the XTR111. In the datasheet it shows if you have a connection between the Set pin and Rload then you can generate a 0-10v Output. I was wondering…
    • Answered

  • RE: XTR111: bandwidth limit of 20kHz

    Resolved
    Hello Luis, Thank you so much for the detailed response. Indeed, I had done similarly during my tests, removing diodes, protections and other accessories that could limit the bandwidth either at the input or output paths. I can confirm your results. I…
    • Answered

  • XTR111: XTR 111 Thermal pad connection not done. Does this give error output?

    Resolved
    Part Number: XTR111 The xtr111 is not working as intended. But When i reduce the supply voltage below 11.53 it gives a linear 4 - 20mA with my pwm input. But as soldered the part by hand, we cannot ensure the bottom thermal pad is connected to ground…
    • Resolved
    • Answered

  • XTR111: Amplifiers forum

    Resolved
    Part Number: XTR111 Other Parts Discussed in Thread: XTR300 , OPA2197 clarification needed on output ripple / noise characteristics of the part. page 15 of the datasheet shows 2 figures 39, 40 of output ripple with and without filtering, what is not clear…
    • Resolved

  • XTR111: XTR111: EF Pin Timing Implementation

    TI Thinks Resolved
    Part Number: XTR111 XTR111: EF Pin Timing - Amplifiers forum - Amplifiers - TI E2E support forums Hi Team, I have question about the timing for Error Flag Trip. You could refer to the post in the above. I see that the delay time is about 665us. But this…

  • XTR111: Level shift of 0V input and Transconductance trim

    TI Thinks Resolved
    Part Number: XTR111 Hi, support team My customer has the questions as follow: In the datasheet of XTR111, shown that the XTR111 offers a low offset voltage error at the input for the signal source, which may not deliver the 0V in a single supply circuit…

  • XTR111: Current Sink Vs Source

    TI Thinks Resolved
    Part Number: XTR111 Other Parts Discussed in Thread: XTR110 , XTR300 , XTR305 Hi We are using XTR111 as a voltage to current converter for a 4-20mA signal in the transmitter. Many times customers asked whether we provide current output as source or sink…

  • XTR111: RTI Noise

    TI Thinks Resolved
    Part Number: XTR111 Other Parts Discussed in Thread: XTR300 , Hi, Can you please help me to relate the Figure 5(0.1Hz to 10Hz NOISE, RTI) to Figure 39 (Output Noise without Filter into 500Ω) in the datasheet (SBOS375C –NOVEMBER 2006–REVISED JUNE 2011) if…

  • XTR111: Recommended operating voltage

    TI Thinks Resolved
    Part Number: XTR111 Hi Team, Customer is looking for the typical value that can be used in the EF pin. Below is the details. "We need to apply the EF pin of XTR111 to the controller. In the datasheet, the absolute maximum rating shows (Vvsp) + 0.5. The…
    • Answered

  • XTR111: EF pin with 0V input

    Resolved
    Part Number: XTR111 HI, We have a design that uses two XTR111s and the EF pin is high on one and low on the other when Vin=0V, and the output is open circuit for both of them. Does having a 0V input put the XTR111 in a no man land state for the EF pin…
    • Resolved

Didn't find what you are looking for? Post a new question.