• XTR300: Vin vs Vout data

  

  Y.Ottey

  TI Thinks Resolved

  Part Number: XTR300 Other Parts Discussed in Thread: XTR305 , , TIPD155 Dear TI Team Our customers are requesting Vin vs Vout measurement data when using the XTR300 and XTR305 in voltage output mode. (To understand the error of Vout with respect to Vin …

  • 4 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• XTR300: What's the maximum voltage the output DRV pin could bear?

  

  Tess Chen

  Resolved

  Part Number: XTR300 Hi, What's the maximum voltage the output DRV pin could bear for XTR300? Thanks. Best Regards, Tess Chen

  • Resolved

  • 3 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• XTR300: Optimizing XTR300 for 1Khz signals

  

  Peter Berben

  Resolved

  Part Number: XTR300 Other Parts Discussed in Thread: , TINA-TI I'm currently evaluating the XTR300 using the evaluation board. I noticed that with the default board configuration any input signal above 50Hz gets distorted and hence at 1KHz the input/output…

  • Resolved

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum
Answered

• RE: XTR300: analog output linearity

  

  Tamara M Alani

  Resolved

  Hi Alen, We haven't heard from you in a while. We hope the issue was resolved. Closing this thread now. Reply to re-open if you have any additional questions.

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

• XTR300: Imon Disconnected

  

  Ryan Hunnicutt

  TI Thinks Resolved

  Part Number: XTR300 When operating the XTR300 in open loop mode, we notice that Icopy does not output to Imon. Please advise how to internally connect Imon to the current mirror in open loop mode.

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

• XTR300: Max Current Consumption and Input Power Requirement

  

  Bhautik Ramoliya98

  TI Thinks Resolved

  Part Number: XTR300 Hello there, Hope you are doing well. In one of my system i want to use two XTR300 (one for voltage output and one for current output). Those both XTR300 will be operated from the same power supply . I have different choice from below…

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum
Answered

• XTR300: IA input has high bias current (40~50uA) in Spice model

  

  user1929517

  Resolved

  Part Number: XTR300 Hello, I have found a problem with XTR300 spice model. In my simulation with the spice model that downloaded from TI webside, the IA input is measured too high bias current in a range from 40uA to 50uA according to different resistance…

  • Resolved

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum
Answered

• XTR300: XTR300 XTR305

  

  Eric Cui13

  Resolved

  Part Number: XTR300 Other Parts Discussed in Thread: XTR305 Hi, What is the difference between the XTR300 and XTR305? Thank you.

  • Resolved

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• XTR300: XTR300 Error Flags's pull-up resister.

  

  Steven He92

  Resolved

  Part Number: XTR300 Dear Sir, XTR300 Error flags: EF_CM, EF_LD, EF_OT pull-up resister can put 1Kohm or 4.7Kohm ? Please you kindly review & advise. Thanks! Steven

  • Resolved

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum
Answered

• XTR300: Output expression For +-10V Output, XTR300

  

  Ignacio Diz Castro

  Resolved

  Part Number: XTR300 Other Parts Discussed in Thread: XTR111 Dear Sirs Our Incoming XTR300 Based Design Will Output +-10V Or +-24mA (Depending on M2 State) Design Its Based On tiduah1 www.ti.com/.../tiduah1.pdf For Current Output, Simulation Works Fine…

  • Resolved

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

Didn't find what you are looking for? Post a new question.