Search tips
Showing 20,896 results View by: Thread Post Sort by
    Answered

  • TPS551892-Q1: About inductance values

    Resolved
    Part Number: TPS551892-Q1 Tool/software: Is the inductance 8.2uH appropriate in the figure? According to the data manual, 4.7uH is appropriate in boost mode but 4.7uH is small in buck mode, so I chose 8.2uH. The design parameters are input voltage…
    • Resolved

  • RE: TAS5825M: TAS5825M Inductive whistling problem

    hi Pan pls check below link for how to perform tuning in our DSP. https://www.ti.com/lit/an/slaa894/slaa894.pdf?ts=1756859005602&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FTAS5805M thanks jesse

  • UCC28951: magnetizing Inductance

    TI Thinks Resolved
    Part Number: UCC28951 Tool/software: Vin MIN : 400VDC VinmAx : 950VDC Vin ( Typ ) : 600VDC 1. the question is primary magnetizing inductance of a psfb transformer should be selected considering Max input voltage or minimum Input Voltage ? Considering…

  • MCF8329EVM: What is the expected behaviour if the value entered for inductance is lower than the actual inductance? What if it's higher?

    Part Number: MCF8329EVM Other Parts Discussed in Thread: MCF8329A Tool/software: I've been having some trouble getting a motor to behave as expected with the EVM, and discovered a discrepancy today. The datasheet for the motor lists the inductance as…

  • TPS92200: TPS92200D2 behavior when driving an inductive load (coil)

    Part Number: TPS92200 Other Parts Discussed in Thread: DRV104 , DRV110 Tool/software: Hi. I am evaluating the TPS92200D2 for a constant current control application. It works fine with a resistive load, but when using an inductive load (coil), I observed…
    • Answered

  • TCAN1044A-Q1: TCAN1044A-Q1 the common mode inductance

    Resolved
    Part Number: TCAN1044A-Q1 Other Parts Discussed in Thread: TCAN1472-Q1 Tool/software: Hi Team, Background is that currently the customer wants us to remove the common mode inductance on the CAN output, but through the EMC mapping, we find that the stability…
    • Resolved
    • Answered

  • LMR51420: inductance selection

    Resolved
    Part Number: LMR51420 Other Parts Discussed in Thread: LMR51430 Tool/software: Hi TI experts, My customer used to use LMR51430YDDCR for power supply and input voltage range is from 18V to 30V(TYP 24V). Output is 5V/3A. Inductance is 3.3uF, same as…
    • Resolved

  • LDC1614EVM:External inductive iron core coil measurement fail

    TI Thinks Resolved
    Part Number: LDC1614EVM Other Parts Discussed in Thread: LDC1614 Tool/software: To measure the inductance change by connecting the external inductive iron core coil I manufactured to the LDC 1614 EVM substrate, the measurement was carried out in the…

  • TMS320F280049: Three phase 115 VAC 400Hz induction motor-pump for hydraulic application

    TI Thinks Resolved
    Part Number: TMS320F280049 Hello, We are in search of a three phase controller reference design for an induction motor ( with no feedback sensor) for a hydraulic pump. What TI would recommend for this application ? Would a V/F control be sufficient…
    • Answered

  • TPS54160: Products with low inductance values

    Resolved
    Part Number: TPS54160 Other Parts Discussed in Thread: LMR38020 , TPS54260 Tool/software: Hi, I am looking for a DCDC that can be used with the following input and output conditions. I searched on Webench and found TPS54160, but the inductance value…
    • Resolved

Didn't find what you are looking for? Post a new question.