Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed the week of November 23.

TPD12S520: Schematci Review

Part Number: TPD12S520
Other Parts Discussed in Thread: AM5728, TPD12S521

Hi TI Team,

Please have your technical team review the attached schematics incorporating the TI Single-Chip HDMI Receiver Port Protection and Interface Device and share your feedback and recommendations for design improvements, including any changes to enhance Functional & EMI/EMC performance.

Attached the schematic for your reference.

TI TPD12S520 HDMI Interface Review.pdf 

Regards

Bharath Kumar C

  • Review Summary — TPD12S520 on AM5728 HDMI Port

    1. Device selection mismatch — highest priority

    The schematic uses the TPD12S520 on the AM5728 HDMI output (source/transmitter) path. The TPD12S520 is intended for HDMI receivers/sinks; using it in a transmitter/source design is a device-selection error, and TPD12S521 is the source-side alternative. 1

    This affects the direction of the integrated level translators and HPD/DDC/CEC buffering, so it must be resolved before the remaining items are meaningful. Please confirm the intended direction of this port (AM5728 driving a display vs. receiving).

    2. Missing bias / pull-up components

    Your sheet shows 5V_SUPPLY (pin 1) and LV_SUPPLY (pin 2, VDD_3V3) with only 100 nF decoupling (C1141, C1142). The following are specified and appear absent:

    Pin Required component Note
    5V_SUPPLY 47 kΩ bias resistor Supply connections require the specified bias resistors and capacitors, not only direct power and decoupling 2
    LV_SUPPLY 10 kΩ series resistor 3
    CEC_IN 47 kΩ pull-up to 3.3 V 3
    HPD_IN 100 kΩ pull-up to 3.3 V Required for the internal level shifter and HPD connection detection; removing it eliminates HPD functionality 4

    Your existing pull-up networks (R671–R674 on the LV side, R675/R677–R679 on the 5 V side) need to be checked against these values per pin — I cannot confirm individual net assignments from the single sheet provided.

    3. TMDS signal integrity / EMI concerns

    Two items in your TMDS path warrant attention:

    • 220 pF series capacitors (C551–C558) on the TMDS lines. Series AC coupling of this value on TMDS is not part of the TPD12S520 reference implementation. The device itself is specified at 0.8 pF TMDS capacitance with 0.05 pF matching between each differential pair precisely to preserve eye margin 5 — adding large series capacitance and pull-down resistors (R452–R455, 22.6 kΩ) directly degrades that margin. Please confirm the design intent here.
    • TMDS routing through U43. From the sheet, the chokes (FL1–FL4, DLW21SN900HQ2) route toward the connector while the U43 TMDS pins appear stubbed/floating. Protected TMDS lines must pass through the device, not bypass it. This needs verification on the full schematic.
  • Hi Chuck Branch,

    Thanks for your quick response & review comments, its helped a lot to us to in figuring out this basic mistake happened in our schematic design.

    Actually from TI SITARA AM5728 Processor we are driving or sending the Video media signals via HDMI interface to 7inch TFT Module,

    & we are not receiving any Video Media Signal via HDMI Input Signal from external world to processor.

    Hence we updated schematics with correct HDMI Single Port Transmitter device part number from TI,

    So please review attached schematics and provide your comments accordingly.

    HDMI Interface Section for TI IC TPD12S521 Mfr Review.pdf

  • Bharath,

    If that is your port direction, then the current schematic looks correct.

    Regards,

    Chuck

  • Hi Chuck,

    Thanks for your confirmation.

    Regards

    Bharath