TUSB9261DEMO: TUSB9261DEMO is not detected mSATA device

satyanarayana P G64

Part Number: TUSB9261DEMO
Other Parts Discussed in Thread: TUSB9261

hi,

we have TUSB9261DEMO device and it is connected with SATA drive and it is ok.

our requirement is to access mSATA drive, we have designed the hardware which has mini D type connector thru which mSATA is connected.

The interface between TUSB9261DEMO and our hardware is SATA to D-type converter cable.

please suggest what to do to access mSATA thru TUSB9261DEMO.

Regards,

satya

over 6 years ago

0 Brian Quach over 6 years ago

TI__Expert 4325 points

Hi,
I have tested TUSB9261DEMO with mSATA SSD before using an off-the-shelf SATA-to-mSATA adapter card. The card has built-in voltage regulator to power the mSATA device. For example: www.amazon.com/.../B004YKJ5TE
Regards,
Brian

0 satyanarayana P G64 over 6 years ago in reply to Brian Quach

Expert 1330 points

hi,

can you provide the SATA-to-mSATA interface details, which will be helpful for us to make adapter card.

regards,
satya

0 Brian Quach over 6 years ago in reply to satyanarayana P G64

TI__Expert 4325 points

Hi, we cannot assist with developing this adapter, but you can purchase on here: www.amazon.com/.../ref=twister_B07GDV6DPF
It is not expensive and there are many companies making this kind of adapter. Otherwise, you may refer to mSATA and SATA specification directly if you wish to develop your own.
Regards,
Brian.

0 satyanarayana P G64 over 6 years ago in reply to Brian Quach

Expert 1330 points

Hi,

not for developing the adapter to know interface connections between SATA-to-mSATA. we had SATA to eSATA cable but we to have an idea about it. Is there any deviation in SATA-to-mSATA interface.

regards,

satya

0 Brian Quach over 6 years ago in reply to satyanarayana P G64

TI__Expert 4325 points

Hi,

I'm not familiar with eSATA. mSATA and SATA have the same electrical interface. Only the pin mapping and voltage supply are different.

Regards,

Brian

0 satyanarayana P G64 over 6 years ago in reply to Brian Quach

Expert 1330 points

hi,

can you share the pin mapping and voltage supply details.

BR
satya

0 Brian Quach over 6 years ago in reply to satyanarayana P G64

TI__Expert 4325 points

Hi, that is not a TI specific standard so please refer to SATA industry specs.

Regards,
Brian

0 satyanarayana P G64 over 6 years ago in reply to Brian Quach

Expert 1330 points

Hi,

please let me know the TUSB9261 detecting memory capacity, since we are facing the problem with 126GB and 256GB and it is fine with 16GB

regards

satya

0 Brian Quach over 6 years ago in reply to satyanarayana P G64

TI__Expert 4325 points

Hi, there is no limit on drive capacity. It may be some limitation of your disk formatting. I have tested up to 3.0TB without issues. Please try the latest FW on the TUSB9261 product page.
Regards,
Brian

0 satyanarayana P G64 over 6 years ago in reply to Brian Quach

Expert 1330 points

Hi,

TUSB9261DEMO is detected 256GB drive. it is a format issue.

Thanks for your support.

please let me know apart from adapter, if we do connections through single strand wires is it ok to check SATA to mSATA interface.

Is any buffers required before sata drive like SN75LVCP600SDSKT to sata connector.

Regards,

satya

0 Brian Quach over 6 years ago in reply to satyanarayana P G64

TI__Expert 4325 points

Hi Satya,

Single strand wire is not suitable. The data lines must maintain 100-ohm differential impedance. A buffer should not be required unless the trace length is very long.

Regards,

Brian

0 satyanarayana P G64 over 6 years ago in reply to Brian Quach

Expert 1330 points

Hi Brian,

when we cut short the length of cable the device is detected by TUSB9261DEMO and now it is working fine.

thanks for your support

satya

0 Brian Quach over 6 years ago in reply to satyanarayana P G64

TI__Expert 4325 points

Hi Satya,

You're welcome. Please mark this thread as resolved. Thanks!

Regards,
Brian

Interface

Interface forum

TUSB9261DEMO: TUSB9261DEMO is not detected mSATA device