• State TI Thinks Resolved
  • Locked Locked
  • Replies 7 replies
  • Answers 1 answer
  • Subscribers 22 subscribers
  • Views 1143 views
  • Users 0 members are here
Support feedback
Options
Options
Related

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Request to suggest suitable buffer

Madhu Sharma
Expert 2915 points

Other Parts Discussed in Thread: SN74HC241, SN74LVT16245A, CD74HC243, TXB0104, SN74AVC4T774, SN74LVT16245B

Hi,

I need a buffer with 8 lines, with  2 groups of 4 lines each. Both the group directions should be controlled by separate direction control line (Please refer below image).  I request you to suggest a suitable buffer for this configuration ( preferably small packages lilke TSSOP, QFN or BGAs).

Regards

Madhu

  • 0
    Guru 319830 points

    Bidirectional buffers are only available as voltage translators. However, as far as I can see, none of them has the required configuration.

    It should be possible to combine two unidirectional buffers; the SN74HC241 has one inverting and one non-inverting OE input, which should match with your DIR signals.

  • 0 in reply to Clemens Ladisch
    Expert 2915 points
    Hi,

    Thanks for the reply.

    I need a buffer with properties same as SN74LVT16245A, but with 8 bits, divided into 2 banks ( 4 lines in each bank), operating at 3.3V.

    Please let me know if you need any more inputs for proper buffer selection.

    Regards
    Madhu
  • 0 in reply to Madhu Sharma
    Guru 319830 points

    There is no single device with these properties.

    Use two SN74HC241‍s, or two CD74HC243‍s.

  • 0 in reply to Clemens Ladisch
    Expert 2915 points
    Hi,

    Thanks for the reply.

    Can I use any translators ( like, SN74AVC4T774 or TXB0104) ?

    If yes, is there any translators with Ioh= 32mA and Iol=64mA?

    Regards
    Madhu
  • 0 in reply to Madhu Sharma
    Guru 319830 points

    Thank you very much for keeping the required drive strenth a secret.

    64 mA at 3.3 V requires that you combine at least three outputs for one bit. So, SN74LVC32245.

    What is the actual problem you're trying to solve?

  • 0 in reply to Clemens Ladisch
    TI__Guru 62930 points
    Thank you , Clemens , for all your suggestions to find the right solution for Madhu.
    If I could add , sn74LVT16245B can be considered. It has higher drive strength than LVC devices and have 2 direction control bits. As you rightly mentioned , the DIR control is present for bidirectional transceivers.
    www.ti.com/.../sn74lvt16245b.pdf
  • 0 in reply to ShreyasRao
    Expert 2915 points

    Hi Shreyas,

    Actually I require a buffer to drive 8 gpio lines from a FPGA, connecting to a VME connector. Out of 8 lines, 4 should be controlled with one DIR line and other 4 with other line ( Please refer first figure below). Since this kind of buffer is not available, I am planning to use two level translator ICs instead of one ( Please refer second figure below). Since I am connecting the lines to a connector, drive strength must be atleast 12mA ( all GPIO inputs and outputs are 3.3V level)

    I prefer some 20-TSSOP or smaller packages ( even smaller BGAs are fine) since there is a space constraint in the board.

    Regards

    Madhu