• State Resolved
  • Locked Locked
  • Replies 4 replies
  • Subscribers 31 subscribers
  • Views 297 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

AM2632: PRP Ethernet

D Bennett
Prodigy 10 points
Part Number: AM2632
Other Parts Discussed in Thread: AM3356, AM3357, AM3358, AM3359, AM4376, AM4377, AM4378, AM4379, AM5716, AM5718, AM5726, AM5728, AM5746, AM5748, AM5749, AM6548, AMIC110

Does the PRU-ICSS on the AM2632 support PRP ethernet mode?

I see PRP support for other Sitara processors with PRU-ICSS, but not on the AM263x specifically.

If not, would a software-only solution be possible to implement PRP on the AM2632?

  • 0
    TI__Mastermind 33336 points

    Hi Bennett,

    D Bennett said:
    I see PRP support for other Sitara processors with PRU-ICSS, but not on the AM263x specifically.

    Could you please share the end use case details?

  • 0 in reply to Nilabh Anand
    TI__Mastermind 33336 points
    D Bennett said:
    If not, would a software-only solution be possible to implement PRP on the AM2632?

    It could be possible but we have no plans to implement it, it would be upon your digression to implement it.

  • +1 in reply to Nilabh Anand
    Prodigy 10 points

    I am selecting a processor for an embedded engine controller that will require PRP ethernet communications.
    Two physical ethernet connections with the same IP and MAC address (per PRP requirements). Speed is 10/100 (Gbit not required). Data rate is low (less than 100kb/sec)
    TI shows Sitara processors with PRU-ICSS software for HSR/PRP support for the following:
    www.ti.com/.../PRU-ICSS-INDUSTRIAL-SW
    ARM-BASED PROCESSORS
    AM3356 — Sitara processor: Arm Cortex-A8, PRU-ICSS, CAN
    AM3357 — Sitara processor: Arm Cortex-A8, EtherCAT, PRU-ICSS, CAN
    AM3358 — Sitara processor: Arm Cortex-A8, 3D graphics, PRU-ICSS, CAN
    AM3359 — Sitara processor: Arm Cortex-A8, EtherCAT, 3D, PRU-ICSS, CAN
    AM4376 — Sitara processor: Arm Cortex-A9, PRU-ICSS
    AM4377 — Sitara processor: Arm Cortex-A9, PRU-ICSS, EtherCAT
    AM4378 — Sitara processor: Arm Cortex-A9, PRU-ICSS, 3D graphics
    AM4379 — Sitara processor: Arm Cortex-A9, PRU-ICSS, EtherCAT, 3D graphics
    AM5716 — Sitara processor: Arm Cortex-A15 & DSP
    AM5718 — Sitara processor: Arm Cortex-A15 & DSP, multimedia
    AM5726 — Sitara processor: dual Arm Cortex-A15 & dual DSP
    AM5728 — Sitara processor: dual Arm Cortex-A15 & dual DSP, multimedia
    AM5746 — Sitara processor: dual arm Cortex-A15 & dual DSP, ECC on DDR and secure boot
    AM5748 — Sitara processor: dual arm Cortex-A15 & dual DSP, multimedia, ECC on DDR and secure boot
    AM5749 — Sitara processor: dual Arm Cortex-A15 & dual DSP, multimedia, ECC on DDR, secure boot, deep learning
    AM6548 — Quad Arm® Cortex®-A53 and dual Arm Cortex-R5F SitaraTm processor with gigabit PRU-ICSS, 3D graphics
    AMIC110 — Sitara processor: Arm Cortex-A8, 10+ Ethernet protocols

    Will PRP mode also be possible on the Sitara AM263x processors?

  • 0 in reply to D Bennett
    TI__Mastermind 33336 points
    D Bennett said:
    I am selecting a processor for an embedded engine controller that will require PRP ethernet communications.
    Two physical ethernet connections with the same IP and MAC address (per PRP requirements). Speed is 10/100 (Gbit not required). Data rate is low (less than 100kb/sec)

    Hi Bennett,

    Since the data rate is quite low, it should be possible to implement on R5F core also.

    D Bennett said:
    Will PRP mode also be possible on the Sitara AM263x processors?

    We have taken it in our CCB. We will internally discuss it. I will not be able to comment on availability now