This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Where are Labs for Tm4c123 Launch Pad, please ?

Hi,

I have studied the TM4c123 videos that review the 123 product.

These videos refer-to various Labs - perhaps 10 in all - not sure.

I have found Lab 1 on youtube.com but where are they available from TI?

I have done much searching within TI.Com as well as with google - no luck so far.

TIA for your assistance,

Rob

  • Thanks Kel,
    As I mentioned in my original post I have all of these vids that you found. They are just an introduction.
    They are NOT the "Labs".
    I have only found 1 of the "Labs", and I think there are 10 of them.
    Thanks,
    Rob
  • Hi Robert,

    Sorry, I did not check the videos in the link I provided. I am not sure there are detailed videos for the other "Labs".

    But, I think the workbook pdf from the link I provided above is sufficient enough to provide detailed information about the "Labs", which you can learn from.

    - kel
  • Hello Robert

    The 1st video link in the post from Kel will take you to video page. There is a "i" button which will open related labs on the bottom of the video from which you can pick the other videos

    Regards
    Amit
  • Thanks again Kel,

    I listened to all of the introductory vids, about 14 of them.
    Throughout those vids they refer to "Labs" at various times and even mention:
    "this will be covered in Lab 5"
    "this will be covered in Lab 10"

    And Lab 1 is available on youtube. Here, check it out:
    www.youtube.com/watch

    Thanks for all your help and please let me know if you come across these Labs.

    Best regards,
    Rob
  • Thanks for reply Amit,

    I have been there .....
    These are the same vids that are listed in the Wiki text.
    These are the vids I have listened-to.

    In both cases, (the Wiki text and the i button) the videos are the 15 Introductory vids and the single Lab, namely Lab 1

    It is in the Introductory vids that various mentions are made to various of the "Lab" vids, but only Lab 1 seems to appear anywhere.

    Thanks,
    Rob
  • robert palma said:

    have studied the TM4c123 videos that review the 123 product.

    These videos refer-to various Labs - perhaps 10 in all - not sure.

     Good and I appreciate it, it is the right way to do things.. Not some guru there "do a search...."

    robert palma said:

    I have found Lab 1 on youtube.com but where are they available from TI?

    I have done much searching within TI.Com as well as with google - no luck so far.

     And this is not so simple but I can help you not with simple search but pointing where they are, open this page where you land on from launchpad

    training.ti.com/tm4c123g-launchpad-workshop-series;tisearch=Search-EN-Everything

     here you get access to all video and learning material bur leave me help you dig in where you failed, open this page:

    training.ti.com/tm4c123g-launchpad-workshop-series-3-15-tivaware-initialization-and-gpio

    at bottom you can see "Workshop Material" list, click on installation file and you get a self expanding executable where I think all file you are searching for are. I report here for your convenience:

    software-dl.ti.com/trainingTTO/trainingTTO_public_sw/GSW-TM4C123G-LaunchPad/TM4C123GLaunchPadWorkshopSetup.exe

     About our Markel guru forever answering do a search, I suppose this is liked just to Blake or not? It seem very useless and also confuse our good Amit.

     There where good guru and point collector liked by some staff people.....

     If this doesn't answer ask again eventually reposting all your need, this forum is no more focused on question of good people and volunteer seems biased off reading just last answer.

     Amit, please ask insert link to page containing labs material or just redirect with a line of instruction on web.

  • Hi Roberto,

    Thank-you for your kind reply.

    I was not aware of the:    trainig.ti.com   URL

    I have all of the files installed now.  :-)

    I can see that a video was made of LAB 1 but not for the others.

    This is fine. The 336 page workbook pdf is very good and I will go through that completely.

    Thanks again to all who posted to help me.

    This is a good forum !

    Best regards,

    Robert