Seft Tunning Regulator - help with " include "inc/lm4f230h5qr.h". "

Kiet Tran

Hi everyone, i have a project Seft Tunning Regulator control motor DC, but a have a problem with build this project, it 's include "inc/lm4f230h5qr.h".

I added in include option, and file search path like this:

Sorry because i am not good at english, and thanks for reading this. Please help me.

over 10 years ago

0 Petrei over 10 years ago

Guru 26105 points

Hi,

Since you use the Tiva version 2.1.1.71 - did you checked if that file really exists inside inc/ folder? My guess is not - that file really does not exist there. So you need to set your project to use (and include) the file(s) for the corresponding Tiva microcontroller equivalent with your actually one. On Tiva micros page should be an application note describing the equivalents.

An alternative would be to use an older driverlib,specifically written for LM4F, but suggest the first option since for production LM4F does not exists anymore.

0 Kiet Tran over 10 years ago in reply to Petrei

Prodigy 60 points

Thanks you for your answer,
I uploaded the project on the top, file Tiva TI code.rar.
What sould i do now Petrei? thanks you again.

0 Kiet Tran over 10 years ago in reply to Petrei

Prodigy 60 points

Thanks you for your answer,
I uploaded the project on the top, file Tiva TI code.rar.
What sould i do now Petrei? thanks you again.

0 Amit Ashara over 10 years ago in reply to Kiet Tran

TI__Guru**** 244440 points

Hello Kiet

Include file LM4F does not exist in TivaWare 2.1.1.71 release. You would need to check the equivalent TM4C123 device for the same using the following link and instead use its file as the include file

e2e.ti.com/.../271820

Regards
Amit

0 Petrei over 10 years ago in reply to Kiet Tran

Guru 26105 points

Hi,

I do not know all details of your project - before continuing please see also this page:

Also you can search TI site for older StellarisWare software - there were some examples for BLDC motors, (versions #< 10000).

0 Amit Ashara over 10 years ago in reply to Amit Ashara

TI__Guru**** 244440 points

Hello Kiet

Thanks Petrei. I almost forgot about the StellarisWare Resource.

http://www.ti.com/tool/sw-lm3s

Regards
Amit

0 Kiet Tran over 10 years ago in reply to Amit Ashara

Prodigy 60 points

Thank you everyone.
I use Amit's method by install "StellarisWare® for LM3S MCUs – April 2013 Release (v10636) " and it's work.

0 Amit Ashara over 10 years ago in reply to Kiet Tran

TI__Guru**** 244440 points

Hello Kiet,

May I suggest moving to TivaWare altogether?

Regards
Amit

0 cb1 over 10 years ago in reply to Kiet Tran

Guru 47900 points

Kiet Tran said:
... install "StellarisWare® for LM3S MCUs – April 2013 Release (v10636) " and it's work.

That's very surprising. As a long-term user of (first) LM3S (to include the very early 28 pin devices) and then LX4F (which is poster's device - there never were LM4F devices produced) it is noted that v10636 AVOIDS the LX4F family - covers (just) LM3S.

Version 9453 of the original StellarisWare was (and remains) the most current version of StellarisWare which covers (both) LM3S & LX4F (poster's part).

0 Amit Ashara over 10 years ago in reply to cb1

TI__Guru**** 244440 points

Hello cb1

Yes, I do think there has been an issue in the version number reported as 10636 has only LM3 files

Regards
Amit

Arm-based microcontrollers

Arm-based microcontrollers forum

Seft Tunning Regulator - help with " include "inc/lm4f230h5qr.h". "