• State Resolved
  • Locked Locked
  • Replies 6 replies
  • Subscribers 78 subscribers
  • Views 678 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Linux/MSP-EXP430FR2433: MSP-EXP430FR2433

Gaurav Saxena78
Prodigy 50 points
Part Number: MSP-EXP430FR2433

Tool/software: Linux

Dear,

I have a launchpad purchased 2yrs ago but not used, today when i tried to use it on my linux laptop (Manjaro), initially it showed ttyACM port, 2 numbers, when i tried to download sample program, it started ezfet firmware update after 100%, it gave me some error, so I tried restarting, but now it doesnot show serial ports. lsusb command however show this

Bus 001 Device 002: ID 2047:0203 Texas Instruments

could someone please point me to the right direction.

Regards

Gaurav Saxena

  • 0
    Prodigy 50 points

    Dear,

    Update on my winxp it shows 2 HID devices but no serial ports.

    Any Help is appriciated.

    Regards

    Gaurav Saxena

  • 0 in reply to Gaurav Saxena78
    TI__Mastermind 38295 points

    Hi 

    Can you change to a WIN10 computer to check if the Launchpad is work?

  • 0 in reply to Gary Gao
    Prodigy 50 points

    Hi,

    Will surly try on a win10 os, but it may take some time, abandoned windows way back.

    Regards

    Gaurav

  • 0 in reply to Gary Gao
    Prodigy 50 points

    Hi,

    checked on win10 OS, however i think port are not enumerating, check the screenshot below,

    Regards

    Gaurav

  • 0 in reply to Gaurav Saxena78
    TI__Mastermind 38295 points

    Hi Gaurav

    Have you install the drivers? You can down load it here http://www.ti.com/tool/mspds?DCMP=msp430&HQS=mspds

    More information about the debugger you can refer to http://www.ti.com/tool/mspds?DCMP=msp430&HQS=mspds

    Best regards

    Gary

  • 0 in reply to Gary Gao
    Prodigy 50 points

    Hi Gary,

    Thanks for your help, I had not installed driver, after you posting the link, I installed driver in both linux (seems like installer on linux at least for me is broken it does not show EULA or any other text in information box, but it seems it installed correctly) and windows, but that does not seems to correct my problem, then I decided to have a try at CCS V9, after installing CCS, when i created new project, wizard gave me an option to identify board, clicking on that ccs guided me to recover my board, dont exactly remember that steps, but from memory

    1. First it told me that my board need to be recovered, clicked on recover, red (LED101) and green led (LED102), flashed for some time.

    2. It gave me some error after some time. disconnected board and connected it again.

    3. Againg clicked on identify, red (LED101) and green led (LED102), flashed for some time, information box told me firmware need to be updated, clicked update button, red (LED101) and green led (LED102), bliked in no particular order, after a minute or two, identification process completed. 

    4. Tried MSP430 Blink the LED Demo - Software Toggle P1.0, LED01 started blinking. :-)

    Must appriciate your efforts and this great forum. Now need to grab manuals and start learning. will keep you busy ;-)

    Regards

    Gaurav

**Attention** This is a public forum