Other Parts Discussed in Thread: PMP
Hi ,
I use origin sdk 7.04.00.03 to make a sdcard and plug in J6 EVM board .
But there is no any boot loader message , the first line is
"[ 1.891481] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250" .
How do I modify and then show up the bootloader message ?
Attachment is the boot log.
[ 1.891481] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud = 3000000) is a 8250
[ 1.902186] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20
[ 1.909173] [drm] Initialized drm 1.1.0 20060810
[ 1.924175] brd: module loaded
[ 1.932576] loop: module loaded
[ 1.935985] (stk) :sysfs entries created
[ 1.939974] (stk) : debugfs entries created
[ 1.944259] (hci_tty): inside hci_tty_init
[ 1.948913] (hci_tty): allocated 249, 0
[ 1.955116] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[ 1.961882] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.970463] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[ 1.980966] scsi0 : ahci_platform
[ 1.984764] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 338
[ 1.994086] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.006777] usbcore: registered new interface driver asix
[ 2.012376] usbcore: registered new interface driver ax88179_178a
[ 2.018646] usbcore: registered new interface driver cdc_ether
[ 2.024660] usbcore: registered new interface driver smsc95xx
[ 2.030594] usbcore: registered new interface driver net1080
[ 2.036413] usbcore: registered new interface driver cdc_subset
[ 2.042512] usbcore: registered new interface driver zaurus
[ 2.048386] usbcore: registered new interface driver cdc_ncm
[ 2.054876] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.061451] ehci-pci: EHCI PCI platform driver
[ 2.066058] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.071778] usbcore: registered new interface driver cdc_wdm
[ 2.077644] usbcore: registered new interface driver usb-storage
[ 2.084785] mousedev: PS/2 mouse device common for all mice
[ 2.092795] i2c-core: driver [rtc-ds1307] using legacy suspend method
[ 2.099282] i2c-core: driver [rtc-ds1307] using legacy resume method
[ 2.106332] omap_rtc 48838000.rtcss: rtc core: registered 48838000.rtcss as rtc0
[ 2.114692] i2c /dev entries driver
[ 2.119422] tvp5158 1-0058: Unable to of_probe
[ 2.123897] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 2.130283] ov1063x 1-0037: Failed writing register 0x0103!
[ 2.135894] ov1063x: probe of 1-0037 failed with error -121
[ 2.142428] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
[ 2.148620] vip 48970000.vip: No explicit pinctrl resources data.
[ 2.155699] vip 48970000.vip: loading firmware vpdma-1b8.bin
[ 2.162163] DRA7xx Radio probe done
[ 2.166110] Driver for 1-wire Dallas network protocol.
[ 2.171593] vpe 489d0000.vpe: Device registered as /dev/video0
[ 2.177479] vip 48970000.vip: VPDMA firmware loaded
[ 2.182479] vip1-s1: Port A enabled but no endpoints found
[ 2.187885] vip1-s0: Port B enabled but no endpoints foundvip1-s1: Port B enabled but no endpoints found
[ 2.198309] coproc iva_coproc: probe
[ 2.202189] Adding alias for supply vdd,iva_coproc -> vdd,4a0025cc.voltdm
[ 2.209025] Adding alias for supply vbb,iva_coproc -> vbb,4a0025cc.voltdm
[ 2.216646] coproc iva_coproc: coproc_probe result=0
[ 2.221709] coproc dsp_coproc: probe
[ 2.225382] Adding alias for supply vdd,dsp_coproc -> vdd,4a0025e0.voltdm
[ 2.232252] Adding alias for supply vbb,dsp_coproc -> vbb,4a0025e0.voltdm
[ 2.240137] coproc dsp_coproc: coproc_probe result=0
[ 2.249200] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.258219] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517
[ 2.264862] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral
[ 2.272412] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517
[ 2.279067] platform 480b4000.mmc: Driver omap_hsmmc requests probe deferral
[ 2.336983] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.398760] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.407131] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3
[ 2.427489] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3
[ 2.433808] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
[ 2.440129] alg: skcipher: setkey failed on test 5 for ecb-des-omap: flags=100
[ 2.447780] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
[ 2.455859] alg: skcipher-ddst: setkey failed on test 5 for ecb-des-omap: flags=100
[ 2.468735] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
[ 2.474519] omap-sham 4b101000.sham: initialization failed.
[ 2.480154] omap-sham: probe of 4b101000.sham failed with error -22
[ 2.487136] usbcore: registered new interface driver usbhid
[ 2.492732] usbhid: USB HID core driver
[ 2.498223] hwspinlock_user gatemp: requested 10 hwspinlocks
[ 2.504653] remoteproc0: 58820000.ipu is available
[ 2.509586] remoteproc0: Note: remoteproc is still under development and considered experimental.
[ 2.518628] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[ 2.529135] remoteproc0: Direct firmware load failed with error -2
[ 2.535431] remoteproc0: Falling back to user helper
[ 2.540625] remoteproc1: 55020000.ipu is available
[ 2.545526] remoteproc1: Note: remoteproc is still under development and considered experimental.
[ 2.554694] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[ 2.565237] remoteproc1: Direct firmware load failed with error -2
[ 2.571660] remoteproc2: 40800000.dsp is available
[ 2.576560] remoteproc2: Note: remoteproc is still under development and considered experimental.
[ 2.585575] remoteproc1: Falling back to user helper
[ 2.590694] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[ 2.601233] remoteproc2: Direct firmware load failed with error -2
[ 2.607829] remoteproc3: 41000000.dsp is available
[ 2.612730] remoteproc3: Note: remoteproc is still under development and considered experimental.
[ 2.621766] remoteproc2: Falling back to user helper
[ 2.626965] remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed.
[ 2.637559] remoteproc3: Direct firmware load failed with error -2
[ 2.643855] remoteproc3: Falling back to user helper
[ 2.653960] tlv320aic3x-codec 0-0018: Failed to get supply 'IOVDD': -517
[ 2.660733] tlv320aic3x-codec 0-0018: Failed to request supplies: -517
[ 2.667418] i2c 0-0018: Driver tlv320aic3x-codec requests probe deferral
[ 2.674329] tlv320aic3x-codec 1-0018: Failed to get supply 'IOVDD': -517
[ 2.681108] tlv320aic3x-codec 1-0018: Failed to request supplies: -517
[ 2.687766] i2c 1-0018: Driver tlv320aic3x-codec requests probe deferral
[ 2.694666] tlv320aic3x-codec 1-0019: Failed to get supply 'IOVDD': -517
[ 2.701423] tlv320aic3x-codec 1-0019: Failed to request supplies: -517
[ 2.708081] i2c 1-0019: Driver tlv320aic3x-codec requests probe deferral
[ 2.714982] tlv320aic3x-codec 1-001a: Failed to get supply 'IOVDD': -517
[ 2.721731] tlv320aic3x-codec 1-001a: Failed to request supplies: -517
[ 2.728402] i2c 1-001a: Driver tlv320aic3x-codec requests probe deferral
[ 2.735591] platform bt_sco_card: Driver asoc-simple-card requests probe deferral
[ 2.743931] asoc-simple-card asoc-simple-card.0: hdmi-hifi <-> 58040000.encoder mapping ok
[ 2.753973] davinci-mcasp 48464000.mcasp: DAI is shared
[ 2.759784] davinci-mcasp 48468000.mcasp: numevt will be ignored due to errata i868
[ 2.768651] davinci-mcasp 48474000.mcasp: DAI is shared
[ 2.773946] davinci-mcasp 48474000.mcasp: numevt will be ignored due to errata i868
[ 2.782092] davinci-mcasp 48478000.mcasp: numevt will be ignored due to errata i868
[ 2.790258] davinci-mcasp 4847c000.mcasp: numevt will be ignored due to errata i868
[ 2.798681] davinci_evm primary_sound: ASoC: CODEC (null) not registered
[ 2.805440] davinci_evm primary_sound: snd_soc_register_card failed (-517)
[ 2.812374] platform primary_sound: Driver davinci_evm requests probe deferral
[ 2.820135] dra7xx-jamr3-snd jamr3_sound: ASoC: CODEC (null) not registered
[ 2.827167] dra7xx-jamr3-snd jamr3_sound: failed to register sound card -517
[ 2.834258] platform jamr3_sound: Driver dra7xx-jamr3-snd requests probe deferral
[ 2.842696] oprofile: using timer interrupt.
[ 2.847060] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 2.853647] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.859069] TCP: cubic registered
[ 2.862398] Initializing XFRM netlink socket
[ 2.866710] NET: Registered protocol family 17
[ 2.871205] NET: Registered protocol family 15
[ 2.875737] Bridge firewalling registered
[ 2.879788] can: controller area network core (rev 20120528 abi 9)
[ 2.886056] NET: Registered protocol family 29
[ 2.890535] can: raw protocol (rev 20120528)
[ 2.894864] 8021q: 802.1Q VLAN Support v1.8
[ 2.899134] Key type dns_resolver registered
[ 2.903426] NET: Registered protocol family 41
[ 2.908487] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.voltdm
[ 2.914787] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.voltdm
[ 2.922659] Power Management for TI OMAP4+ devices.
[ 2.927724] ThumbEE CPU extension supported.
[ 2.932019] Registering SWP/SWPB emulation handler
[ 2.938498] vmmcwl_fixed: disabling
[ 2.941998] regulator-dummy: disabling
[ 2.945960] dmm 4e000000.dmm: workaround for errata i878 in use
[ 2.953678] dmm 4e000000.dmm: initialized all PAT entries
[ 2.959469] platform omapdrm.0: Driver omapdrm requests probe deferral
[ 2.967384] evm_3v3_sd: 3300 mV
[ 2.970867] evm_3v3_sw: 3300 mV
[ 2.974132] evm_3v3_sw: supplied by sysen1
[ 2.978661] aic_dvdd: 1800 mV
[ 2.981757] aic_dvdd: supplied by evm_3v3_sw
[ 2.986314] vtt_fixed: 1350 mV
[ 2.989521] vtt_fixed: supplied by sysen2
[ 2.994601] tvp5158 1-0058: Unable to of_probe
[ 2.999149] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 3.088932] asoc-simple-card bt_sco_card: bt-sco-pcm <-> 48478000.mcasp mapping ok
[ 3.097642] ALSA sound/core/init.c:213 cannot find the slot for index 0 (range 0-1), error: -16
[ 3.106379] davinci_evm primary_sound: ASoC: can't create sound card for card DRA7xx-EVM: -16
[ 3.114981] davinci_evm primary_sound: snd_soc_register_card failed (-16)
[ 3.121827] davinci_evm: probe of primary_sound failed with error -16
[ 3.124080] mmc1: host does not support reading read-only switch. assuming write-enable.
[ 3.125996] mmc1: new high speed SDHC card at address 1234
[ 3.142165] mmcblk0: mmc1:1234 SA04G 3.70 GiB
[ 3.148432] mmcblk0: p1 p2
[ 3.151517] dra7xx-jamr3-snd jamr3_sound: multicodec <-> 48474000.mcasp mapping ok
[ 3.179665] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.186310] [drm] No driver support for vblank timestamp query.
[ 3.192291] omapdrm omapdrm.0: No connectors reported connected with modes
[ 3.199211] [drm] Cannot find any crtc or sizes - going 1024x768
[ 3.209437] [drm] Enabling DMM ywrap scrolling
[ 3.220177] Console: switching to colour frame buffer device 128x48
[ 3.232090] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
[ 3.238121] omapdrm omapdrm.0: registered panic notifier
[ 3.243468] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
[ 3.249694] tvp5158 1-0058: Unable to of_probe
[ 3.254167] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 3.273709] mmc2: BKOPS_EN bit is not set
[ 3.281776] mmc2: new high speed DDR MMC card at address 0001
[ 3.288060] mmcblk1: mmc2:0001 MMC08G 7.25 GiB
[ 3.292783] mmcblk1boot0: mmc2:0001 MMC08G partition 1 8.00 MiB
[ 3.298924] mmcblk1boot1: mmc2:0001 MMC08G partition 2 8.00 MiB
[ 3.305835] mmcblk1: p1 p2
[ 3.310138] mmcblk1boot1: unknown partition table
[ 3.315973] mmcblk1boot0: unknown partition table
[ 3.316972] davinci_mdio 48485000.mdio: davinci mdio revision 1.6
[ 3.316979] davinci_mdio 48485000.mdio: detected phy mask fffffff3
[ 3.321523] libphy: 48485000.mdio: probed
[ 3.321530] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown
[ 3.321537] davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown
[ 3.321888] tvp5158 1-0058: Unable to of_probe
[ 3.321903] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 3.322564] cpsw 48484000.ethernet: Detected MACID = d4:f5:13:88:5a:40
[ 3.323294] tvp5158 1-0058: Unable to of_probe
[ 3.323308] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 3.323951] cpsw 48484000.ethernet: cpsw: Random MACID = 62:ee:bc:7f:73:12
[ 3.325125] tvp5158 1-0058: Unable to of_probe
[ 3.325140] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 3.397612] omap_rtc 48838000.rtcss: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 3.406827] tvp5158 1-0058: Unable to of_probe
[ 3.411387] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 3.421369] ALSA device list:
[ 3.424355] #0: DRA7xx-WiLink
[ 3.427622] #1: HDMI 58040000.encoder
[ 3.431476] #2: DRA7xx-JAMR3
[ 4.981139] EXT4-fs (mmcblk0p2): recovery complete
[ 4.992324] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 5.000562] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 5.009395] devtmpfs: mounted
[ 5.012567] Freeing unused kernel memory: 308K (c08e2000 - c092f000)
INIT: version 2.88 booting
Starting udev
[ 5.492512] udevd[1213]: starting version 182
[ 5.791428] Bluetooth: Core ver 2.18
[ 5.857141] NET: Registered protocol family 31
[ 5.861613] Bluetooth: HCI device and connection manager initialized
[ 5.937011] Bluetooth: HCI socket layer initialized
[ 5.941923] Bluetooth: L2CAP socket layer initialized
[ 5.967304] Bluetooth: SCO socket layer initialized
[ 6.067867] tvp5158 1-0058: Unable to of_probe
[ 6.072364] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.089297] (stc): chnl_id list empty :4
[ 6.093238] (stk) : st_kim_start[ 6.107266] tvp5158 1-0058: Unable to of_probe
[ 6.111734] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.201626] (stk) :ldisc_install = 1
[ 6.284756] remoteproc3: failed to load dra7-dsp2-fw.xe66
[ 6.351748] remoteproc2: powering up 40800000.dsp
[ 6.362840] CAN device driver interface
[ 6.366922] remoteproc2: Booting fw image dra7-dsp1-fw.xe66, size 948568
[ 6.374290] tvp5158 1-0058: Unable to of_probe
[ 6.379862] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.387668] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=fce3c000, irq=353)
[ 6.402670] remoteproc0: failed to load dra7-ipu1-fw.xem4
[ 6.454077] omap_hwmod: mmu0_dsp1: _wait_target_disable failed
[ 6.459961] omap-iommu 40d01000.mmu: 40d01000.mmu: version 3.0
[ 6.465881] omap-iommu 40d02000.mmu: 40d02000.mmu: version 3.0
[ 6.468553] m25p80 spi32766.0: s25fl256s1 (32768 Kbytes)
[ 6.468628] 10 ofpart partitions found on MTD device spi32766.0
[ 6.468631] Creating 10 MTD partitions on "spi32766.0":
[ 6.468635] 0x000000000000-0x000000010000 : "QSPI.SPL"
[ 6.496864] 0x000000010000-0x000000020000 : "QSPI.SPL.backup1"
[ 6.499791] random: nonblocking pool is initialized
[ 6.514089] tvp5158 1-0058: Unable to of_probe
[ 6.514144] 0x000000020000-0x000000030000 : "QSPI.SPL.backup2"
[ 6.514846] 0x000000030000-0x000000040000 : "QSPI.SPL.backup3"
[ 6.515541] 0x000000040000-0x000000140000 : "QSPI.u-boot"
[ 6.517645] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os"
[ 6.518376] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env"
[ 6.519047] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1"
[ 6.519734] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel"
[ 6.520422] 0x0000009e0000-0x000002000000 : "QSPI.file-system"
udevd[1507]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
udevd[15[ 6.658733] remoteproc2: remote processor 40800000.dsp is now up
08]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/s[ 6.669052] virtio_rpmsg_bus virtio0: rpmsg host is online
cripts/mount.sh': No such file or directory
[ 6.676193] remoteproc2: registered virtio0 (type 7)
[ 6.678072] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x36
[ 6.678193] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x37
[ 6.678288] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x65
[ 6.678404] rpmsg_rpc rpmsg2: probing service rpmsg-dce-dsp with src 1024 dst 101
[ 6.715717] rpmsg_rpc rpmsg2: published functions = 8
[ 6.721704] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.759556] tvp5158 1-0058: Unable to of_probe
[ 6.772044] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.835883] remoteproc1: powering up 55020000.ipu
[ 6.841524] remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 3480836
[ 6.851642] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1
[ 6.913245] remoteproc1: remote processor 55020000.ipu is now up
[ 6.919849] virtio_rpmsg_bus virtio1: rpmsg host is online
[ 6.925621] tvp5158 1-0058: Unable to of_probe
[ 6.930221] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.936167] remoteproc1: registered virtio1 (type 7)
[ 6.941716] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x65
[ 6.949149] rpmsg_rpc rpmsg3: probing service dce-callback with src 1024 dst 101
[ 6.957366] tvp5158 1-0058: Unable to of_probe
[ 6.961942] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.967938] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x66
[ 6.975439] rpmsg_rpc rpmsg4: probing service rpmsg-dce with src 1025 dst 102
[ 6.983427] tvp5158 1-0058: Unable to of_probe
[ 6.988201] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 6.994198] rpmsg_rpc rpmsg3: published functions = 4
[ 6.999417] rpmsg_rpc rpmsg4: published functions = 8
udevd[1527]: failed to execute '/etc/udev/scripts/mount.sh' '/etc/udev/scripts/mount.sh': No such file or directory
udevd[1528]: failed to execute '/etc/udev/scripts/mount.sh' '/et[ 7.196964] (stk) :ldisc installation timeoutc/udev/scripts/mount.sh': No such file or directory
[ 7.202564] (stk) :ldisc_install = 0[ 7.236141] tvp5158 1-0058: Unable to of_probe
[ 7.240654] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 7.637460] tvp5158 1-0058: Unable to of_probe
[ 7.643480] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 7.658617] dwc3 48890000.usb: otg: primary host xhci-hcd.0.auto registered
[ 7.665610] dwc3 48890000.usb: otg: shared host xhci-hcd.0.auto registered
[ 7.674713] dwc3 48890000.usb: otg: can't start till gadget registers
[ 7.683387] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.683469] tvp5158 1-0058: Unable to of_probe
[ 7.683481] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 7.699609] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 7.709766] xhci-hcd xhci-hcd.1.auto: irq 439, io mem 0x488d0000
[ 7.716038] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.722887] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.730162] usb usb1: Product: xHCI Host Controller
[ 7.735305] usb usb1: Manufacturer: Linux 3.14.63 xhci-hcd
[ 7.741112] usb usb1: SerialNumber: xhci-hcd.1.auto
[ 7.746464] hub 1-0:1.0: USB hub found
[ 7.750545] hub 1-0:1.0: 1 port detected
[ 7.754727] tvp5158 1-0058: Unable to of_probe
[ 7.759251] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 7.761223] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.764886] using random self ethernet address
[ 7.764892] using random host ethernet address
[ 7.765294] usb0: HOST MAC de:31:b3:3c:d5:86
[ 7.765316] usb0: MAC 1a:4d:24:73:c5:aa
[ 7.765345] g_ncm gadget: NCM Gadget
[ 7.765348] g_ncm gadget: g_ncm ready
[ 7.765354] dwc3 48890000.usb: otg: gadget gadget registered
[ 7.800820] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 7.800832] tvp5158 1-0058: Unable to of_probe
[ 7.800842] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 7.819002] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 7.825817] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.833312] usb usb2: Product: xHCI Host Controller
[ 7.838234] usb usb2: Manufacturer: Linux 3.14.63 xhci-hcd
[ 7.843740] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 7.849048] hub 2-0:1.0: USB hub found
[ 7.852829] hub 2-0:1.0: 1 port detected
[ 7.856981] tvp5158 1-0058: Unable to of_probe
[ 7.861445] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 7.868191] tvp5158 1-0058: Unable to of_probe
[ 7.874871] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 8.206975] (stk) : timed out waiting for ldisc to be un-installed
[ 8.320029] (stk) :ldisc_install = 1(stk) :ldisc installation timeout
[ 9.319871] (stk) :ldisc_install = 0[ 9.336737] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory
bootlogd.
ALSA: Restoring mixer settings...
No state is present for card DRA7xxWiLink
Found hardware: "DRA7xx-WiLink" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card DRA7xxWiLink
No state is present for card H58040000encode
Found hardware: "HDMI_58040000_e" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card H58040000encode
No state is present for card DRA7xxJAMR3
Found hardware: "DRA7xx-JAMR3" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card DRA7xxJAMR3
Thu Mar 24 18INIT: Entering runlevel: 5
Configuring network interfaces... [ 9.886489] net eth0: initializing cpsw version 1.15 (0)
[ 9.895339] tvp5158 1-0058: Unable to of_probe
[ 9.899954] i2c 1-0058: Driver tvp5158 requests probe deferral
[ 9.970866] net eth0: phy found : id is : 0x20005c7a
[ 9.981337] 8021q: adding VLAN 0 to HW filter on device eth0
udhcpc (v1.22.1) started
Sending discover...
[ 10.316973] (stk) : timed out waiting for ldisc to be un-installed
[ 10.430023] (stk) :ldisc_install = 1(stk) :ldisc installation timeout
[ 11.429857] (stk) :ldisc_install = 0(stk) : timed out waiting for ldisc to be un-installed
[ 12.538693] (stk) :ldisc_install = 1Sending discover...
(stk) :ldisc installation timeout
[ 13.539869] (stk) :ldisc_install = 0(stk) : timed out waiting for ldisc to be un-installed
[ 14.648701] (stk) :ldisc_install = 1(stk) :ldisc installation timeout
[ 15.649865] (stk) :ldisc_install = 0Sending discover...
(stk) : timed out waiting for ldisc to be un-installed
[ 16.758720] (stk) :ldisc_install = 1[ 17.090915] omap_hwmod: mmu_ipu2: _wait_target_disable failed
[ 17.756972] (stk) :ldisc installation timeout
[ 17.761175] (stk) :ldisc_install = 0(stk) : timed out waiting for ldisc to be un-installed
[ 18.763708] Bluetooth: st_register failed -22
No lease, forking to background
done.
Starting system message bus: dbus.
UIM SYSFS Node Found at /sys/./devices/kim/install
Starting uim-sysfs daemon.
uim:@ main
uim:install = /sys/./devices/kim/install
uim:dev_name = /sys/./devices/kim/dev_name
uim:baud_rate = /sys/./devices/kim/baud_rate
uim:flow_cntrl = /sys/./devices/kim/flow_cntrl
uim:begin polling...
Starting telnet daemon.
Starting tiipclad daemon
GateMP support enabled on host
Opened log file: lad.txt
numProcessors = 5 id = 0 baseId = 0
Spawned daemon: /usr/bin/lad_dra7xx
.
Starting rpcbind daemon...rpcbind: cannot create socket for udp6
rpcbind: cannot create socket for tcp6
done.
creating NFS state directory: done
starting statd: done
NFS daemon support not enabled in kernel
Starting syslogd/klogd: done
Starting thttpd.
Enabling thermal zones...
Stopping Bootlog daemon: bootlogd.
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org dra7xx-evm /dev/ttyO0
Arago 2013.10 dra7xx-evm /dev/ttyO0
dra7xx-evm login: root
root@dra7xx-evm:~# cat /proc/version
Linux version 3.14.63 (tiiappadmin@swubn01) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 SMP PREEMPT Thu Mar 24 23:48:42 IST 2016
root@dra7xx-evm:~# ps
PID USER VSZ STAT COMMAND
1 root 1320 S init [5]
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW< [kworker/0:0H]
6 root 0 SW [kworker/u4:0]
7 root 0 SW [rcu_preempt]
8 root 0 SW [rcu_sched]
9 root 0 SW [rcu_bh]
10 root 0 SW [migration/0]
11 root 0 SW [migration/1]
12 root 0 SW [ksoftirqd/1]
13 root 0 SW [kworker/1:0]
14 root 0 SW< [kworker/1:0H]
15 root 0 SW< [khelper]
16 root 0 SW [kdevtmpfs]
17 root 0 SW [kworker/u4:1]
68 root 0 SW [kworker/0:1]
395 root 0 SW< [writeback]
398 root 0 SW< [bioset]
399 root 0 SW< [crypto]
401 root 0 SW< [kblockd]
532 root 0 SW< [ata_sff]
543 root 0 SW [khubd]
550 root 0 SW [irq/324-4807000]
589 root 0 SW [irq/212-0-0021]
594 root 0 SW [irq/325-4807200]
615 root 0 SW [irq/326-4806000]
617 root 0 SW [irq/327-4807a00]
623 root 0 SW [kworker/1:1]
645 root 0 SW< [devfreq_wq]
738 root 0 SW< [rpciod]
755 root 0 SW [kswapd0]
756 root 0 SW [fsnotify_mark]
757 root 0 SW< [nfsiod]
816 root 0 SW [irq/369-OMAP HD]
928 root 0 SW [scsi_eh_0]
929 root 0 SW< [scsi_tmf_0]
932 root 0 SW [kworker/u4:2]
943 root 0 SW [spi1]
945 root 0 SW [spi2]
948 root 0 SW [spi32766]
989 root 0 SW< [kpsmoused]
1012 root 0 SW [kworker/0:2]
1033 root 0 SW [irq/27-talert]
1071 root 0 SW [kworker/1:2]
1079 root 0 SW [irq/436-extcon_]
1082 root 0 SW [irq/437-extcon_]
1093 root 0 SW [kworker/0:3]
1099 root 0 SW [irq/355-4846800]
1100 root 0 SW [irq/354-4846800]
1101 root 0 SW [irq/359-4847800]
1102 root 0 SW [irq/358-4847800]
1103 root 0 SW [irq/361-4847c00]
1104 root 0 SW [irq/360-4847c00]
1125 root 0 SW< [deferwq]
1130 root 0 SW [irq/228-mmc1]
1132 root 0 SW [kworker/1:3]
1133 root 0 SW [kworker/u4:3]
1135 root 0 SW [kworker/u4:4]
1141 root 0 SW [mmcqd/1]
1161 root 0 SW [mmcqd/2]
1162 root 0 SW [mmcqd/2boot0]
1163 root 0 SW [mmcqd/2boot1]
1187 root 0 SW< [kworker/0:1H]
1188 root 0 SW [kworker/0:4]
1189 root 0 SW [jbd2/mmcblk0p2-]
1190 root 0 SW< [ext4-rsv-conver]
1213 root 3116 S /lib/udev/udevd -d
1370 root 0 SW< [kworker/u5:0]
1375 root 0 SW< [hci0]
1378 root 0 SW< [hci0]
1380 root 0 SW< [kworker/u5:1]
1429 root 3036 S /lib/udev/udevd -d
1430 root 3036 S /lib/udev/udevd -d
1460 root 0 SW< [pvr_timer]
1473 root 0 SW< [kworker/1:1H]
1529 root 0 SW< [usb_otg]
1537 root 0 SW [irq/438-dwc3]
1665 root 1868 S udhcpc -R -b -p /var/run/udhcpc.eth0.pid -i eth0
1672 messageb 2348 S /usr/bin/dbus-daemon --system
1679 root 1172 S /usr/bin/uim -f /sys/./devices/kim
1682 root 1868 S /usr/sbin/telnetd
1687 root 9708 S /usr/bin/lad_dra7xx -g -l lad.txt
1696 rpc 1932 S /usr/sbin/rpcbind
1709 rpcuser 1676 S /usr/sbin/rpc.statd
1720 root 1868 S /sbin/syslogd -n -O /var/log/messages
1723 root 1868 S /sbin/klogd -n
1728 nobody 2252 S /usr/sbin/thttpd -d /srv/www -p 8080
1735 root 2588 S -sh
1736 root 1872 S /sbin/getty 38400 tty1
1740 root 2156 R ps
root@dra7xx-evm:~#
