Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] J784S4XEVM: How to enable main domain watchdog?

    Part Number: J784S4XEVM Other Parts Discussed in Thread: TDA4VM The j721e/TDA4VM has SOC watchdog enabled. How to enable the same on J784s4?

  • [FAQ] AM64X/AM62X: How do I route the same GPIO bank interrupts to different destination cores?

    Part Number: AM6442 How do I route the same GPIO bank interrupts to different destination cores? Example: I want to route the GPIO0_37 pin interrupt to R5F0_0 and the GPIO0_38 pin interrupt to R5F0_1. when I was selecting the above pin combination…

  • [FAQ] AM625: Long Term Effects of Simultaneously Power-Down Sequencing of all Voltage Rails

    Part Number: AM625 I'm working with a customer that is using the TPS6521908 as their PMIC, and therefore, should in nearly all cases have a controlled power-down sequencing of all the AM62x voltage rails. However, it is still possible that they could…

  • [FAQ]: Transitioning the GPIO userspace interface from SYSFS to Chardev

    This information applies to Linux SDK Version 9.0 and prior. For more up to date information, refer to this FAQ: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1494485/faq-processor-sdk-getting-started-with-gpios-in-linux-using…

  • [FAQ] SK-AM62: How to build initramfs into kernel Image

    Part Number: SK-AM62 There are cases the initramfs should be used for Linux root filesystem. Please see the kernel documentation < Documentation/filesystems/ramfs-rootfs-initramfs.rst > for the details of initramfs. There are two ways to use initramfs…

  • [FAQ] TDA4VM: How to reduce the EthFW initialization time to avail CPSW H/W Switch functionality as soon as possible after the core boot up in Vision Apps use-case?

    Part Number: TDA4VM How to reduce the EthFW initialization time to avail CPSW H/W Switch functionality as soon as possible after the core boot up in Vision Apps use-case?

  • [FAQ] TDA4VM: How do I enable CAN channels on Gateway/Ethernet Switch/Industrial (GESI) expansion card when using J721E EVM from Linux A72?

    Part Number: TDA4VM How do I enable CAN channels on Gateway/Ethernet Switch/Industrial (GESI) expansion card when using J721E EVM from Linux A72?

  • [FAQ] How to set up an EtherCAT System with AM6xx MainDevice and AM64/AM243 SubDevice using CODESYS Development System

    Other Parts Discussed in Thread: UNIFLASH This FAQ walks the user through setting up an industrial networking EtherCAT system in CODESYS using an AM6xx MainDevice and one-or-more AM64x/AM243x SubDevice(s). Instructions are provided to set up MainDevice…

  • [FAQ] TDA4VM: OpenVX Host on R5F and node Target on A72 (Linux)

    Part Number: TDA4VM How to run OpenVX Host on R5F and a node to run on A72 (Linux) as target?

  • [FAQ] AM623: Decoupling caps on CAP_VDDSx

    Part Number: AM623 Champs, Customer's asking what will happen if the decoupling caps on the CAP* nets below are not installed correctly? Will the device's behavior be well defined in this case (i.e. fail to boot etc) or would it be more sporadic based…

View FAQ threads
  • Threads 197753 Discussions