AFE7422EVM: where can i download AFE GUI (Version 1.8.5 RC4)

Li Yang

Prodigy 100 points

Part Number: AFE7422EVM

I want to download this version

over 4 years ago

0 Vijayendra Varma Siddamsetty over 4 years ago

TI__Genius 11125 points

Hi Yang,

Selecting mode6 in the latest version of GUI would configure the EVM in same mode as shown above (in the older version of GUI).

So you can use the latest GUI available in secure folder for this.

Regards,

Vijay

0 Li Yang over 4 years ago in reply to Vijayendra Varma Siddamsetty

Prodigy 100 points

Hi Vijay

where can i get schematic of the Arria10 EVM mentioned in the pdf above，i want to transplant the FPGA project to TSW14J57 EVM rev E. RX sync does not go to high. I need to compare the difference between the Arria10 EVM and TSW14J57 EVM rev E.

Regards,

Yang

0 Vijayendra Varma Siddamsetty over 4 years ago in reply to Li Yang

TI__Genius 11125 points

Hi Yang,

You can find the Intel Arria 10 dev kit documentation on Intel website below:

https://www.intel.com/content/www/us/en/programmable/products/boards_and_kits/dev-kits/altera/kit-a10-gx-fpga.html

Regards,

Vijay

0 Li Yang over 4 years ago in reply to Vijayendra Varma Siddamsetty

Prodigy 100 points

Hi Vijay

I want to know which Arria10 EVM used in the document.

A10 AFE74xx XCVR 2x44210 JESD Reference Design User Guide.pdf

Regards,

Yang

0 Vijayendra Varma Siddamsetty over 4 years ago in reply to Li Yang

TI__Genius 11125 points

Hi Yang,

Intel Arria 10 GX FPGA Development Kit was used for this. You can refer to the link in my previous reply for Intel webpage of this dev kit.

Regards,

Vijay

0 Li Yang over 4 years ago in reply to Vijayendra Varma Siddamsetty

Prodigy 100 points

Hi Vijay,

Can you help me with this problem,

https://e2e.ti.com/support/rf-microwave-group/rf-microwave/f/rf-microwave-forum/1044327/afe7422evm-can-not-work-in-mode2-and-capture-wrong-data-in-mode3/3864256?tisearch=e2e-sitesearch&keymatch=%25252520user%2525253A496637#3864256

I want to know,if this problem also happens in Ti's Lab. or my operation or power has some problem.

AFE74xx Gui 2.2.9, High Speed Data Converter Pro 5.2.

Yang

0 Vijayendra Varma Siddamsetty over 4 years ago in reply to Li Yang

TI__Genius 11125 points

Hi Yang,

We are seeing issues with Mode2 and 3 in TI lab too. Rx JESD modes with F=3 are not supported by HSDC Pro.

Mode 4 should work robustly.

Regards,

Vijay

0 Li Yang over 4 years ago in reply to Vijayendra Varma Siddamsetty

Prodigy 100 points

Hi Vijay,

Can you help me with this problem in TX mode3.

AFE7422EVM: Every time after send signal, I need to manually force a handshake of JESD204B. - RF & microwave forum - RF & microwave - TI E2E support forums

Regards,

Yang

0 Vijayendra Varma Siddamsetty over 4 years ago in reply to Li Yang

TI__Genius 11125 points

Hi Yang,

As we are discussing this on the other e2e post, I will close this one.

Regards,

Vijay