IWR1642BOOST: TI IWR1642 Evaluation Module

Sharon Naveena Rajan

Part Number: IWR1642BOOST
Other Parts Discussed in Thread: MMWAVE-SDK, , IWR1642

Hello,

I am having trouble using the mmWave Demo visualizer. I am getting a command saying " SDK input version [major, minor ] = [2, 0] not matching [1, 0] reported by target, Hint: Change input version/target and try again. Can you please help me resolving this issue.

Your help is much appreciated. Thank you

Sharon

over 7 years ago

0 Akash Gondalia over 7 years ago

TI__Guru 50240 points

Hi Sharon,

What version of mmWave-SDK binaries have you flashed on your IWR1642BOOST?

Do you know if your IWR1642BOOST is ES1.0 or ES2.0? When did you purchase it?

Cheers,
Akash

0 Sharon Naveena Rajan over 7 years ago in reply to Akash Gondalia

Intellectual 540 points

Hi ,

I dont know when it was purchased. Where can I find the information about ES1.0 or ES2.0. I installed Version 1.0

0 Akash Gondalia over 7 years ago in reply to Sharon Naveena Rajan

TI__Guru 50240 points

Look at the text on the IWR1642 chip on the bottom left corner. If it reads 502 it is ES1.0 and you'll need to use the mmWave-SDK 1.2. If it reads 502A or 502AC then it is ES2.0 and you'll need the mmWave-SDK 2.0.

Match the appropriate version with the visualizer and you should be good to go!

Cheers,
Akash

0 Sharon Naveena Rajan over 7 years ago in reply to Akash Gondalia

Intellectual 540 points

Got it. Thanks

0 Sharon Naveena Rajan over 7 years ago in reply to Akash Gondalia

Intellectual 540 points

Hi ,

The Demo Visualizer was successfully installed according to your instructions. But unfortunately I had to change my laptop and once again when I installed the files , the device was not connected. I have attached the error message. It is only showing "waiting for data" and does not proceed further. Please let me know what has to be done .

Thank You

SharonThe SDK Information and the error message.docx

0 Akash Gondalia over 7 years ago in reply to Sharon Naveena Rajan

TI__Guru 50240 points

Hi Sharon,

You've installed mmWave-SDK version 1.2 but your visualizer has indicated SDK Version 1.0. Please correct this appropriately.

Cheers,
Akash

0 Sharon Naveena Rajan over 7 years ago in reply to Akash Gondalia

Intellectual 540 points

Hi Akash,

Thanks, I changed it accordingly still getting the same notification " waiting for data "

0 Sharon Naveena Rajan over 7 years ago

Intellectual 540 points

Hello Akash,

Hope you're doing good. I am working on IWR1642BOOST EVM for people counting application. Can you please guide me. It will be of great help.

Thank you

Regards,

Sharon

0 Akash Gondalia over 7 years ago in reply to Sharon Naveena Rajan

TI__Guru 50240 points

Hi Sharon,

People Counting is outside the scope of this thread, although if you open up a new one I can ask a People Counting Expert to assist you.

Cheers,
Akash

0 Sharon Naveena Rajan over 7 years ago in reply to Akash Gondalia

Intellectual 540 points

Sure.

0 Sharon Naveena Rajan over 7 years ago

Intellectual 540 points

I created a new thread.

Thank You

Sensors

Sensors forum

IWR1642BOOST: TI IWR1642 Evaluation Module