Which SDK and CCS version do you use? Can you attach what errors you see?

I use CCS 10.3.1 and simplelink_cc13x2_26x2_sdk_5_10_00_48.

Try to use latest simplelink_cc13x2_26x2_sdk_5_20_00_52 and CCS 10.4 to test again. If you still see errors, please attach your errors or screenshot.

Hello, 

These are screenshot of the errors.

It seems you cannot build project successfully. Can you provide complete build log on your CCS console?

Thank you. I have resolved the problem. 

Hello, 

I have run the ZNP project successfully in ccs 10.3.1. I want to use my CC2652RB launchpad implemented the ZNP code  as coordinator and i use another CC2652RB as zed doorlock with running zed doorlock code. How can I do this application . 

I suppose you can run zed_doorlock on your CC2652RB to make it.

I have run zed-doorlock in my CC2652RB and ZNP code in another CC2652RB. These are screenshots of the output of serial port in PuTTy application.   

Try to refer to zed_doorlock readme at dev.ti.com/.../node

Hello sirine,

You can use the ZIGBEE-LINUX-SENSOR-TO-CLOUD demo if you want an out-of-box ZCL application to communicate with your ZNP.  Otherwise you will need to use Z-Tool or your own interface and use MT APIs to register endpoints (AF_REGISTER) and send ZCL messages (AF_DATA_REQUEST) as well as receive them (AF_INCOMING_MSG).  The other option is to use zc_doorlockcontroller application example instead of the ZNP.

Regards,
Ryan

Hello,

I have some questions about Z-stack linux Gateway. the launchpad uses in this application about this link https://software-dl.ti.com/simplelink/esd/zigbee_3_0_Linux/1.0.1/exports/Documents/Z-Stack%20Linux%20Gateway%20-%20User's%20Guide.html#more-configurables is  CC-2652R1 but I have the launchpad CC2652RB. Can you tell me what are the modifications that i should do in this application ? 

You can run ZNP on CC2652RB and all others are the same.

what about the flash image of the CC2652RB ? I can use the CC2652R1LP_GW_ZNP_UART.hex or I use the file of the ZNP code  which is znp_CC2652RB_LAUNCHXL_tirtos_ccs.hex ?

Hello sirine,

You will need to build the CC2652RB ZNP firmware with CCS and use the output hex file.  You should also consider making the changes highlighted in the Zigbee_3_0_Linux_Gateway_1_0_1\Firmware\README.html file.  Please review the following as well:

https://e2e.ti.com/f/1/t/947947 
https://e2e.ti.com/f/1/t/1024945 

Regards,
Ryan

The issue is not your network settings but rather the setup and connection to the ZNP.  Please review the Z-Stack Linux Sensor to Cloud Quick Start Guide and monitor/provide the log from executing zigbeeHAgw as it should reach Phase 5 successful startup. https://e2e.ti.com/support/wireless-connectivity/f/1/t/1003433 

Regards,
Ryan

Hello, 

Thank you for your support?

I have executed zigbeeHAgw and start_application successfully. I add the coordinator and the network has opened but I am enable to add the end_device which is a doorlock sensor. I read the Z-stack Linux Gateway - User's Guide and Developer's Guide very carefully to success the network and  add the device but there's a problem. Can you help me to resolve this problem ?

Did you mean I should install the Zigbee Wireless Sniffer ? 

You can refer to  https://e2e.ti.com/support/wireless-connectivity/zigbee-thread-group/zigbee-and-thread/f/zigbee-thread-forum/699648/faq-zigbee-packet-sniffing-solutions?tisearch=e2e-sitesearch&keymatch=faq%3Atrue to setup sniffer.

Make sure your zed_doorlock has a DEFAULT_CHANLIST which matches the network channel used by the gateway.  ZDAPP_CONFIG_PAN_ID should be 0xFFFF so that any Pan ID can be joined.

Regards,
Ryan

I am using DEFAULT_CHANLIST = 12 in the ZNP and zed_doorlock. and the PAN ID for the ZNP is 0x1234 and for the zed_doorlock is 0xFFFF. 

In the config.ini : DEFAULT_CHANLIST = 12 and PAN ID = 0x1234.

If you mean to use channel 12, you should define DEFAULT_CHANLIST=0x00001000 not 12.

yes, i have defined as 0x000010.

OK. Then, you can setup sniffer and check what happens exactly on channel 12.

//DEFAULT_CHANLIST=0x04000000  // 26 - 0x1A
//DEFAULT_CHANLIST=0x02000000  // 25 - 0x19
//DEFAULT_CHANLIST=0x01000000  // 24 - 0x18
//DEFAULT_CHANLIST=0x00800000  // 23 - 0x17
//DEFAULT_CHANLIST=0x00400000  // 22 - 0x16
//DEFAULT_CHANLIST=0x00200000  // 21 - 0x15
//DEFAULT_CHANLIST=0x00100000  // 20 - 0x14
//DEFAULT_CHANLIST=0x00080000  // 19 - 0x13
//DEFAULT_CHANLIST=0x00040000  // 18 - 0x12
//DEFAULT_CHANLIST=0x00020000  // 17 - 0x11
//DEFAULT_CHANLIST=0x00010000  // 16 - 0x10
//DEFAULT_CHANLIST=0x00008000  // 15 - 0x0F
//DEFAULT_CHANLIST=0x00004000  // 14 - 0x0E
//DEFAULT_CHANLIST=0x00002000  // 13 - 0x0D
DEFAULT_CHANLIST=0x00001000  // 12 - 0x0C
//DEFAULT_CHANLIST=0x00000800  // 11 - 0x0B

Channel list mapping for reference.

Regards,
Ryan 

I think there are no problem but I still disabled to add the zed_doorlock to the gateway.

Your zed_doorlock UART console shows its short address as 0x0000 which is strange to me. Can you use default zed_doorlock example and use CUI to give primary channel to channel 12 to test again.

For reference, here is the default ZED Sample Doorlock CUI view.  Make sure to erase all device memory or reset to FN before programming and attempting to commission the device.

Regards,
Ryan

How I can erase all device memory ? 

This is my screenshot.

It is a CUI option, or you can use CCS Debug Configurations -> Target -> Flash Settings.  Uniflash and Flash Programmer also have Mass Erase options.  Please keep in mind that a sniffer log will help provide additional insight.

Regards,
Ryan

According to your latest screenshot, it looks good to me. Do you try to set primary channel to channel 12 to test again?

THank you. 

It works. I just erase all memory of the device.

Hello, I have a question about z-stack linux gateway.

 can we add zigbee devices from other brands like Tuya to the z-stack linux  gateway of Texas instrument solution ? 

Regards, Sirine.

Hello, 

I have a question related to the gateway application. In the Z-stack Linux Gateway - Developer's Guide. I find this description "The Z-Stack Linux Gateway offering includes a C-based sample Gateway application that is a good starting point for anyone trying to develop their own application. The example, included in the release along with source code, performs basic Gateway functions such as creating the network and adding/controlling common Zigbee devices. It also demonstrates other interesting Zigbee functionality such as creating Groups and Scenes for devices connected to the network."

The code c is in this direction  /ti/Zigbee_3_0_…ource/Projects/zstack/linux/hagateway. 

How  i can compile this code to try the application gateway? 

Regards,

Sirine. 

There may be some confusion, as you already have been based on the screenshots you've provided so far.

Regards,
Ryan

Hello,

Can you  send me please the class and sequence diagrams of the ZNP code? 

Thank you. 

Here is the ZNP documentation available:

https://dev.ti.com/tirex/content/simplelink_cc13x2_26x2_sdk_5_20_00_52/docs/zigbee/html/zigbee/znp_interface.html 
https://dev.ti.com/tirex/explore/node?node=AEEJ0Z3BgvagEoglvx9r1g__pTTHBmu__LATEST 

Regards,
Ryan