CC2538 GW and CC1310

Mark Felberg

Guru 19990 points

Other Parts Discussed in Thread: CC2538, CC2650, CC1310, CC2538EMK, CC1350, CC1200

Can the CC2538 GW support the cc13xx as a device? In the sense if I use the cc13xx with the cc26xx-web-demo supports them?

over 8 years ago

0 YiKai Chen over 8 years ago

Guru 735695 points

No, it can’t.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Ok, What are the devices I can use as a node for GW?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

CC2538 or CC2650.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Ok, another question. Can I add the IP64 to 6lbr webserver?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Yes, it works when I run 6lbr on CC2538DK.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

If I use the LAUCHXXL CC1310, in the path of 6lbr I disabled things I do not need and I have enabled IP64 because I can not display it?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Told you many times that CC1310 is short of flash so there’s no IP64 when you run 6lbr lite.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Understanding if I use CC2538 GW and another cc2538 as a node? It works?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

I also confirm this before and yes again, it will works.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Why I have this error?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Don’t use sudo to run mosquitto.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

If I use "mosquitto" I have the same problem

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Do you use apt-get to install mosquitto? If so, Ubuntu will start the Mosquitto service after install by default.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Yes, i use apt-get install mosquitto. But when I type "mosquitto", i see "opening port 1883, address already is use"

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

That is because mosquitto already is running after you use apt-get install. You don’t have to run it again otherwise you would get this address conflict.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

On this link:processors.wiki.ti.com/.../Cc26xx_contiki_sw_apps, I read that for on led I should write mosquitto_pub -h <broker_ip> ....

But in the broker IP I should put this 0064:ff9b:0000:0000:0000:0000:b8ac:7cbd?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

You should put IP address of your mosquitto MQTT server.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Where can I see this?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

It depends on where you run mosquitto. If I am not wrong, you run it on your InstantContiki and you can use ifconfig to get the IP address .

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Ok. Thanks. I have now come up with two cc2538 chips. Now try the webserver. How can I use the second cc2538 instead of 2650?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

For example, you can run mqtt example under examples/cc2538-common/mqtt-demo to send MQTT messages to IBM QuickStart.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Yes, I can not connect to the flash programmer. I have this error

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Ok It works. my error. Now I access to 6lbr with cc2538dk+enc28j60. Now that sensor i use?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

I had replied you to use mqtt example under examples/cc2538-common/mqtt-demo to send MQTT messages to IBM QuickStart.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Ok, but i have problems to power the cc2538 alone

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

You can connect USB cable to USB socket on CC2538EMK and move jumper from EM power to USB power (red line in the picture).

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Ok how can I proceed? I changed the place to the jumper, should I change something in the code?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Change the jumper and plug it with USB will give power to CC2538. What do you mean "should I change something in the code?"?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

I change the jumper, but not working

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

What FW do you run on CC2538EM and what do you expect?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

I would like to use mqtt-demo. I connected the cc2538 gw and I expect to read the sensor

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Do you download any firmware to CC2538?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

I downloaded the cc2538 firmware on website of texas

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

I use this: cetic 6lbr router and mqtt-demo

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Can you access to your 6lbr page running on CC2538DK?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Yes, but not read the sensor mqtt-demo

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

There is no http server on mqtt-demo so you won't see web page of mqtt-demo.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

But should the sensor appear? How do I use the MQTT-d...

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

I am not sure if MQTT-demo would show on sensor page but if you enable IP64, MQTT messages should send to IBM QuickStart.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

When I insert cc2538dk usb the pc does not read so i'm not sure it works. Also in 6lbr when I enable IP64 and click submit does not change my settings

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

I suggest you to setup sniffer to check what happens over the air.

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

I have only two CC2538! Have you advised me to buy them and do not even work now?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

When I click on submit, the setup not change. Why?

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Do you check what UART output on your CC2538DK?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

If you enable IP64 and submit, does anything output on UART?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

Nothing, the same problem, the IP64 not enable

0 Mark Felberg over 8 years ago in reply to Mark Felberg

Guru 19990 points

Ok, it works!

0 YiKai Chen over 8 years ago in reply to Mark Felberg

Guru 735695 points

Why does it work suddenly?

0 Mark Felberg over 8 years ago in reply to YiKai Chen

Guru 19990 points

The IP64 works because I had a network problem, but now as a node I use it? I have another cc2538 without SmartRF I use for GW

Zigbee & Thread

Zigbee & Thread forum

CC2538 GW and CC1310