Hi,
We have obtained the viewer log file such as the attached file if changing the settings(volume, BQ, DRC, etc.) on the gui after downloading hybridflow5 to TAS5754M/56M evm.
It seems that the same command is repeated to write the value to TAS5754M/56M's registers.
Could you please tell us this reason ?
In addition, does the this procedure need if initializing the necessary registers on the customer's board ?
Hybridflow5_Repetition_Command_File.txt
w 98 01 05 w 98 00 00 w 9a 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05 w 98 01 05 w 98 00 00 w 98 00 2c w 98 01 05
Best regards,
Kato
