TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel
Frequent Questions
  • [FAQ] What is a buffered LOW?

    Tyler Townsend
    Tyler Townsend
    Part Number: TCA9517 Other Parts Discussed in Thread: TCA9617B FAQ: Logic and Voltage Transla tion > IxC >> What is a buffered LOW ? A "buffered LOW" is the output voltage of the buffer when a low voltage input (VIL) is present on the input. This…
    • over 2 years ago
    • Interface
    • Interface forum
  • [FAQ] BQ79631-Q1: What's the meaning of "MISC"?

    Vickie Wu
    Vickie Wu
    Part Number: BQ79631-Q1 Tool/software: Hello, I'm reading the datasheet of BQ79631-Q1, and there is a question about AUX ADC measurements. I see AUX ADC operate MISC measurements including some internal reference voltages. But I couldn't find the full…
    • Answered
    • over 2 years ago
    • Power management
    • Power management forum
  • [FAQ] Why is memcpy so slow on AM6x when copying data from a V4L2 buffer?

    Jianzhong Xu
    Jianzhong Xu
    Part Number: AM62A7 Other Parts Discussed in Thread: AM68A , AM69A , AM62A3 , , AM62A3-Q1 , AM62P Tool/software: I want to copy the data in the V4L2 buffer filled by the CSI RX driver on AM6x. However, the copy is very slow. A 4MB copy takes about…
    • Answered
    • over 2 years ago
    • Processors
    • Processors forum
  • [FAQ] TMS570LC4357: A tool to decode FEE blocks for failure analysis

    QJ Wang
    QJ Wang
    Part Number: TMS570LC4357 Tool/software: FEE data block decoder
    • Answered
    • over 2 years ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • [FAQ] TMS320F28P559SJ-Q1: The procedure to recover from CAN Bus-Off

    QJ Wang
    QJ Wang
    Part Number: TMS320F28P559SJ-Q1 Tool/software: The procedure to recover from CAN Bus-Off
    • Answered
    • over 2 years ago
    • C2000™︎ microcontrollers
    • C2000 microcontrollers forum
  • [FAQ] How to profile CPU Usage with MCU+ SDK?

    Nitika Verma
    Nitika Verma
    Part Number: PROCESSOR-SDK-AM64X Tool/software: How to measure CPU load in an application with FreeRTOS/MCU+ SDK?
    • Answered
    • over 2 years ago
    • Processors
    • Processors forum
  • [FAQ] TDA4VM: How do I use GPIO interrupts in PDK and how are they routed?

    Neehar Sawant
    Neehar Sawant
    Part Number: TDA4VM Tool/software: How do I use GPIO interrupts in PDK and how are they routed in J7 devices?
    • Answered
    • over 2 years ago
    • Processors
    • Processors forum
  • [FAQ] IWRL6432: Is my IWRL6432 an ES1 or ES2 revision?

    Nathan Block
    Nathan Block
    Part Number: IWRL6432 Tool/software: If you are not sure if your IWRL6432 is an ES1 or ES2 revision, use the below table to figure out. All devices ordered from TI in the future will be ES2. TI no longer produces ES1 devices, so this post only refers…
    • Answered
    • over 2 years ago
    • Sensors
    • Sensors forum
  • [FAQ] UCC27311A-Q1: Using a high-side or half-bridge gate driver as a low-side gate driver

    William Moore
    William Moore
    Part Number: UCC27311A-Q1 Tool/software: What are the considerations for using the high-side output of a half-bridge gate driver as a low-side gate driver? When utilizing a half-bridge driver in a typical half-bridge configuration, an internal level…
    • Answered
    • over 2 years ago
    • Power management
    • Power management forum
  • [FAQ] J722SXH01EVM: Attempt to connect to XDS110 failed (on-board USB debugger)

    Neehar Sawant
    Neehar Sawant
    Part Number: J722SXH01EVM Tool/software: I have the following error when trying to connect XDS110 debugger and launch target configuration in CCS: How do I fix this?
    • Answered
    • over 2 years ago
    • Processors
    • Processors forum
<>

View FAQ threads