TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel
Frequent Questions
  • [FAQ] BQ2562x FAQs

    Wyatt Keller
    Wyatt Keller
    Other Parts Discussed in Thread: BQ25620 , BQ25628E , BQ25622E , BQ25628 , BQ25629 , BQ25622 BQ2562x FAQ Home Page This home page is for common questions in relation to the BQ25620, BQ25622, BQ25628, BQ25629, BQ25628E, and BQ25622E. FAQs …
    • Answered
    • over 2 years ago
    • Power management
    • Power management forum
  • [FAQ] BQ25620: How does the charge safety timer work for BQ25620, BQ25622, BQ25622E, BQ25628, BQ25628E, and BQ25629?

    Wyatt Keller
    Wyatt Keller
    Part Number: BQ25620 Other Parts Discussed in Thread: BQ25628E , BQ25622E , BQ25628 , BQ25629 , BQ25622 Tool/software: The safety timer for the BQ25620, BQ25622, BQ25622E, BQ25628, BQ25628E, and BQ25629 functions as a protection against prolonged charging…
    • Answered
    • over 2 years ago
    • Power management
    • Power management forum
  • [FAQ] TUSB1142: How to properly connect the TUSB1142 FLIP pin to the TPS2583xA-Q1 CC controller

    David (ASIC) Liu
    David (ASIC) Liu
    Part Number: TUSB1142 Other Parts Discussed in Thread: TPS25820 , Tool/software: The TUSB1142 design uses the Flip signal from a TPS25820 to switch the SuperSpeed signals from a USB Type C connector. We are not able to get SuperSpeed to work at all.
    • Answered
    • over 2 years ago
    • Interface
    • Interface forum
  • [FAQ] DS280DF810: Why is 25G/28G Retimer PRBS Generator Not Working?

    Drew Miller1
    Drew Miller1
    Part Number: DS280DF810 Other Parts Discussed in Thread: DS250DF410 Tool/software: Introduction: One common debug question when using TI's 25G/28G is why is the PRBS generator not working? This FAQ will review the key criteria for the retimer PRBS generator…
    • over 2 years ago
    • Interface
    • Interface forum
  • [FAQ] PROCESSOR-SDK-AM64X: How to create a PWM using a timer

    Paula Carrillo
    Paula Carrillo
    Part Number: PROCESSOR-SDK-AM64X Tool/software: Hi, can we use a timer to generate a PWM? If so, how could we control/change its frequency and duty cycle while running?
    • Answered
    • over 2 years ago
    • Processors
    • Processors forum
  • [FAQ] TUSB211A: Why does the USB 2.0 redriver not appear to work when taking eye-diagrams?

    Undrea Fields
    Undrea Fields
    Part Number: TUSB211A Tool/software: In order to perform eye-diagram testing, the TUSB211A and other USB 2.0 redrivers must first detect the scope termination after power on or reset. Once termination has been detected, then the redriver will enable the…
    • over 2 years ago
    • Interface
    • Interface forum
  • [FAQ] DS280DF810: Which 25/28G Retimer Should I Select?

    Drew Miller1
    Drew Miller1
    Part Number: DS280DF810 Other Parts Discussed in Thread: DS250DF210 , DS250DF230 , DS250DF410 , DS250DF810 , Tool/software: TI has several retimers in its 25/28G retimer product family. This FAQ breaks down some of the key differences between TI's 25…
    • over 2 years ago
    • Interface
    • Interface forum
  • [FAQ] DS280DF810: How can I calculate estimated signal conditioner power consumption?

    Drew Miller1
    Drew Miller1
    Part Number: DS280DF810 Tool/software: When implementing a signal conditioning device in a system, one design consideration is the device power consumption. In order to address this design consideration, it's valuable to understand how to calculate the…
    • over 2 years ago
    • Interface
    • Interface forum
  • [FAQ] UCC21710-Q1: Schematic and Layout Recommendation

    Sasikala Thangam
    Sasikala Thangam
    Part Number: UCC21710-Q1 Other Parts Discussed in Thread: UCC21710 Tool/software: What is the typical required, recommended schematic and good layout practice for UCC21710Q1 and UCC21710
    • over 2 years ago
    • Power management
    • Power management forum
  • [FAQ] TUSB522P: Where should a USB3 redriver be placed?

    Undrea Fields
    Undrea Fields
    Part Number: TUSB522P Tool/software: The USB3 redriver is meant to recover signal loss from a lossy channel. The redriver is best placed near the end of the channel. For example, in a motherboard application, the redriver is best placed closer to the…
    • over 2 years ago
    • Interface
    • Interface forum
<>

View FAQ threads