Frequent Questions

  • [FAQ] AM62D-Q1 Custom board hardware design – AUDIO-AM62D-EVM Audio Functionality Implementation Related Queries and Design Notes

    Part Number: AM62D-Q1 Other Parts Discussed in Thread: AUDIO-AM62D-EVM Hi TI experts, I am planning to reuse the AM62D-Q1 AUDIO-AM62D-EVM schematics for my custom board design. I see the below schematic sections (pages) added to the AUDIO-AM62D-EVM…

  • [FAQ] AM6421: RESETSTATz output during ROM boot

    Part Number: AM6421 Hello, During a successful QSPI boot, I have captured the following signals: MCU_PORz, RESETSTATz, OSPI_CLK, OSPI_CS. I'm observing that roughly 35mS after RESETSTATz goe high it has a 160uS period where it drops low. Looking at…

  • [FAQ] TDA4VH-Q1: How to configure the SerDes lane for PCIe, USB, Ethernet, and Display in Linux?

    Part Number: TDA4VH-Q1 Other Parts Discussed in Thread: TDA4VH The high speed interfaces on the TDA4x share the SerDes lanes. The lanes can be muxed for different interfaces, but how can I configure them within Linux?

  • [FAQ] AM2754-Q1: Working Configurations for 8S-8S-8S on S28HS512T Serial NOR OSPI Flash

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: SYSCONFIG In MCU+ SDK 11.02, the OSPI and Flash examples are configured by default to operate at the highest protocol: 8D-8D-8D. For configuring 8S-8S-8S SDR Protocol on S28HS512T Serial NOR OSPI…

  • [FAQ] TDA4VH-Q1,TDA4VE,TDAVAL,TDA4VL,TDA4VP-Q1,TDA4AP-Q1: How to reset C7x and load binary faster via CCS

    Part Number: TDA4VH-Q1 Hi, After reset of C7x, i am trying to load newer C7x binary, but the second load takes a lot of time. Could you please help me to solve this issue.

  • [FAQ] AM263P4-Q1: Last 24 bytes of Bank0, Bank1 in OCRAM are no longer visible

    Part Number: AM263P4-Q1 Hi, Regarding the E2E mentioned below, could you please provide us with further information? We are currently using SDK 9.2, and due to our development schedule, we do not have sufficient time to migrate to SDK 11.0. Could you…

  • [FAQ] AM64/AM243: Facing an issue with CCS when trying to flash an image using SBL JTAG UNIFLASH

    Part Number: AM6442 Other Parts Discussed in Thread: UNIFLASH I am trying to flash an image for AM64/AM243 device by loading SBL JTAG UNIFLASH from CCS version 20. *.* , after following the steps mentioned in the MCU+SDK documentation: https://software…

  • [FAQ] BQ25630EVM: .BQZ file for BQ25630 Evaluation Module

    Part Number: BQ25630EVM Other Parts Discussed in Thread: BQ25630 , BQSTUDIO , Please see attached for the BQ25630 BQZ file to be used with BQSTUDIO software. To use the GUI you will need to download Battery management studio software from TI.com,…

  • [FAQ] printf demo for MSPM0 device

    Other Parts Discussed in Thread: LP-MSPM0G3507 printf_to_uart_LP_MSPM0G3507_nortos_ticlang.zip Default UART pin is PA10 and PA11, and it's based on LP-MSPM0G3507 default. Please check corresponding Launchpad's User guide schematic before test. There…

  • [FAQ] TVS2210: TVS2210 Device Part Marking

    Part Number: TVS2210 The device I received is marked as 'TV' but that is not listed as an option in the datasheet.

View FAQ threads