Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 421 results View by: Thread Post Sort by
    Answered

  • ADS131E08: will it work with ADS131E08S capacitors.

    Resolved
    Part Number: ADS131E08 Tool/software: Will the ADS131E08 work with capacitors values which were adjusted for ADS131E08S? The 3ms startup is not used in based aplication with ADS131E08S. ADS131E08 ADS131E08S Bonus question: Can the reference voltage (VREFP…
    • Resolved

  • ADS131E08: ADS131E08 Standard Input range Issues

    Part Number: ADS131E08 Other Parts Discussed in Thread: ADS131M08 , ADS127L18 Tool/software: How do I simply read 0V - 2.4V and get the full range using the ADS131E08? This is my current schematics: AVDD = 3.3V AVSS = 0V INTERNAL VREF = 2.4V All my ADC…

  • ADS131E08: Issue Utilization the Full Range

    Part Number: ADS131E08 Tool/software: We have a design where we'd like to utilize the full, 24-bit range of the ADS131E08 ADC. We expected the full range to be +/-2^23 bits = +/-8,388,608. The positive input voltage range we use is 0 ~ 2.4V, and we…

  • ADS131E08: Wrong ID register value

    Part Number: ADS131E08 Tool/software: Hello Team, During the initialization stage, I am not reading the correct ID register value from the ADC. The expected value for 24-bit, 8-channel configuration is D2h but the response is 00h or 3Fh. Below are the…

  • ADS131E08: Measurement error of 3mV.

    Part Number: ADS131E08 Tool/software: Hello, I'm observing a measurement error of 3mV when comparing readings from voltmeters. I'm using a voltmeter with an internal resistance of 10 GΩ. It seems like something is causing a 3mV voltage…

  • ADS131E08: The calibration of the offsets does not work correctly.

    Part Number: ADS131E08 Tool/software: Hello, After sending the calibration command, I put the ADS in short-circuit mode and performed some acquisitions to check the calibration. The measured values are not very close to 0. Normally, the ENOB for my configuration…
    • Answered

  • ADS131E08: The calibration of the offsets does not work correctly.

    Resolved
    Part Number: ADS131E08 Tool/software: Hello, After sending the calibration command, I put the ADS in short-circuit mode and performed some acquisitions to check the calibration. The measured values are not very close to 0. Normally, the ENOB for my configuration…
    • Resolved

  • ADS130E08: ADS131E08: Sample code

    Part Number: ADS130E08 Other Parts Discussed in Thread: TMS320F28377D , ADS131E08 Tool/software: Can you please share the source code that runs on the TMS320F28377D DSP on ADS130E08 Performance Demonstration Kit？
    • Answered

  • ADS131E08: Unused Bias Amplifier for ADS131E08

    Resolved
    Part Number: ADS131E08 Hello All, I'm using the ADS131E08IPAGR on a medical sensor. I am trying to reduce the power consumption of my board as much as I can to help out with our strain gage drift problems. Basically the lowest power consumption will…
    • Resolved
    • Answered

  • RE: ADS131E08: Read Data with RDATA command and the result is corruption

    Resolved
    Hi he bc, Understood, thanks for confirming. If you need anything else, please start a new thread and we will support you there -Bryan

Didn't find what you are looking for? Post a new question.