Answered

• CC1200: CC1200 Entering RX_FIFO_ERROR

  

  Rio 6

  Resolved

  Part Number: CC1200 Hello, I notice that occasionally CC1200 would enter RX_FIFO_ERROR state. Checking MODEM_STATUS1 byte confirms that it is caused by RXFIFO_OVERFLOW. I am using CRC_OK gpio signal to trigger a read from the fifo (CRC_AUTOFLUSH…

  • Resolved

  • 12 days ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• CC1200: CC1200 Receiver Parameters (LO & IF) for EN300220 Compliance

  

  Mike Wu1

  TI Thinks Resolved

  Part Number: CC1200 Dear TI Support Team, We are currently assisting our client with the EN300220 regulatory certification for their product, which utilizes the CC1200 transceiver. Due to the updated safety regulations (transition period ending in…

  • 3 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum
Answered

• CC1200: CC1200 PLL Unlock Issue after Changing Loop Filter Capacitor to 2200pF

  

  Cameron Yang

  Resolved

  Part Number: CC1200 I am working on a CC1200 design at 188MHz with a 100kbps bit rate and 49.89kHz deviation. I recently changed the loop filter capacitor to 2200pF to improve phase noise/stability. However, this change caused the PLL to unlock (the…

  • Resolved

  • 2 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum
Answered

• CC1200: CC1200 Frequency limit in 400 band

  

  Tero Palmu

  Resolved

  Part Number: CC1200 Hi, Question about CC1200 400MHz band frequency limits. Datasheet specifies lower frequency limit 410MHz for 400MHz band, and I try to understand what is the reason for it. We use this radio chip in our older desings and currently…

  • Resolved

  • 8 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum
Answered

• CC1200: CC1200 GPIO control CC1190

  

  Lance Chang

  Resolved

  Part Number: CC1200 Other Parts Discussed in Thread: CC1190 , , CC1120 Hi E2E, We want to control the CC1190 LNA and PA4 pins using CC1200 GPIOx to achieve the behavior shown in the table below. Application Note AN110, Table 5.1 Can I write…

  • Resolved

  • 8 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum
Answered

• CC1200: Packet RX sensitivity testing with two CC1200 radios

  

  Elaine Ren

  Resolved

  Part Number: CC1200 Tool/software: Hello, I am trying to run some RX sensitivity testing using two CC1200 radios and their dev kit. The purpose is to recreate the sensitivity specified at on the data sheet. One CC1200 is used for packet TX while the…

  • Resolved

  • over 1 year ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• CC1200: CC1200

  

  zou hang

  TI Thinks Resolved

  Part Number: CC1200 Tool/software: Hi, We encountered an issue while debugging CC1200. There are three types of data transmission communication modules, one of which is a chip from another manufacturer with an unknown model and the datarate is 9600…

  • over 1 year ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• CC1200: CC1260

  

  Corey Minyard

  TI Thinks Resolved

  Part Number: CC1200 Other Parts Discussed in Thread: CC1260 I discovered the cc1260, and I've been looking for a chip like this for a long time. I've seen others ask for information, and it says to contact my area sales, but I have been unable to find…

  • 4 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• CC1200: CC1200

  

  zou hang

  TI Thinks Resolved

  Part Number: CC1200 Other Parts Discussed in Thread: CC1310 Tool/software: Hi， Can you provide a reference design circuit for the CC1200 at 351MHz？ thanks!

  • over 1 year ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• CC1200: cc1200

  

  zou hang

  TI Thinks Resolved

  Part Number: CC1200 Tool/software: Hello, I would like to consult a few questions regarding the CC1200: 1、The INVERT_DATA_EN configuration can invert the payload data during both transmission and reception, but the SYMBOL_MAP_CFG should have the same…

  • over 1 year ago
  • Sub-1 GHz
  • Sub-1 GHz forum

Didn't find what you are looking for? Post a new question.