• CDCLVC1110: CDCLVC1110

  

  Madan Chandrashekar

  Part Number: CDCLVC1110 Other Parts Discussed in Thread: CDCLVC1102 What is the maximum capacitive load it can drive? , My design has a clock generator on one board whose output is connected to the CDCLVC1102 and the CDCLVC1102 output is connected to another…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVC1110: Internal circuit of input pin(CLKIN and 1G)

  

  masahiko shimizu

  Resolved

  Part Number: CDCLVC1110 Hi Puneet, I add a question. How mach is the pull-up resistor on 1G pin? Best regards, Shimizu

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVC1110: CDCLVC1110 about the datasheet error information

  

  Mickey Zhang

  Resolved

  Part Number: CDCLVC1110 Hi Team, The customer is using CDCLVC1110. For the CDCLVC1110 datasheet, there are some errors. 1. Pin Configuration diagram Pin Number 10 is Y9 while in Pin Functions table Pin Number 10 is Y8 and Y9 does not have the corresponding…

  • Resolved

  • over 4 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVC1110: Driving ability for capacitive load

  

  Masanori Tachibana

  Resolved

  Part Number: CDCLVC1110 Hello support team, I have a question regarding CDCLVC11xx. - Can CDCLVC11xx drive a CMOS IC (Vcc = 3.3 V) whose input capacitance is 20 pF with 50 MHz clock signal? The period of 50 MHz clock signal is 20 ns. So I think the minimum…

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVC1110: Internal circuit of input pin(CLKIN and 1G)

  

  masahiko shimizu

  Resolved

  Part Number: CDCLVC1110 Hi, Does CDCLVC1110 have internal pull-up or down resistor at input pin(CLKIN and 1G)? Best regards, Shimizu

  • Resolved

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum

• Maximum trace length for the CDCLVC1110

  

  Lucas McKeehan1

  Other Parts Discussed in Thread: CDCLVC1110 , CDCLVC1102 Hi Team, is the CDCLVC1110 able to drive a 100CM tracelength at 40 MHz with 4mil traces with 4 mil spacing? BR, Lucas McKeehan

  • over 8 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• RE: MDC buffer part number required

  

  SVE

  Resolved

  I am discussing on the MDC line. Can i use an IC with part number CDCLVC1110. With this i can drive the MDC line from the processor to all the Slave devices. Plz ignore "operate independently". It is fine even if some slaves see the clock signal…

  • 6 months ago
  • Logic
  • Logic forum

• Reset Fanout 1 to many at 1.8V LVCMOS

  

  Divya jyothi

  Answer Suggested

  Other Parts Discussed in Thread: CDCLVC1110 , SN74AUC1G17 Dear E2E Community, In one of the application we are using reset fan out buffer, please suggest me to select the part number for the below requirement. Input Channel :1 Output channel :Many Voltage…

  • over 3 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum
Answered

• RE: Clock generators, how to evaluate the synchronization of all outputs?

  

  Alan O

  Resolved

  What is the single-ended LVCMOS signaling level (1.5, 1.8, 2.5, 3.3 V?) you need for your target devices? What supply rails do you prefer or have available for the clocks? For CLKGEN board, could you use the following? 8.192 MHz XO --> CDCLVC1102 (1:2…

  • over 4 years ago
  • Clock & timing
  • Clock & timing forum

• RE: Clock skew of 1:40 clock distribution

  

  Alan O

  You would just add the max output skew of the CDCLVC1104 (1st buffer stage) and the max part-to-part skew of the CDCLVC1110s (2nd buffer stage). Worst-case output skew between any 2 outputs of CDCLVC1110s: 50 ps + 0.5 ns = 0.55 ns max (assuming all parts…

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.