Search tips
Showing 21 results View by: Thread Post Sort by
    Answered

  • RE: CSD87502Q2: Access to Altium Lib Package for TI MOSFETs

    Resolved
    Jim, Based on the response we received this morning, I am going to close this one out. There's no more I can do to help at this point.
    • Answered

  • TPS51604-Q1: 3-phase motor driver use-case

    Resolved
    Part Number: TPS51604-Q1 Other Parts Discussed in Thread: CSD87502Q2 , TPS51604 Hi - My customer is planning to use TPS51604-Q1 on their new design. This is a battery powered design. Here was the message: We want to use the TPS51604-Q1 to drive the…
    • Resolved

  • CSD16301Q2: Leakage into drain when off in PSpice for TI

    TI Thinks Resolved
    Part Number: CSD16301Q2 Other Parts Discussed in Thread: CSD87502Q2 , CSD15380F3 Tool/software: Hi, I am a bit afraid this might be a stupid question, but I think I have checked all relevelant datasheet properties like drain to source leakage and reverse…
    • Answered

  • TCAN1042-Q1: CAN Termination control using GPIO

    Resolved
    Part Number: TCAN1042-Q1 Other Parts Discussed in Thread: ESD2CAN24 , CSD , CSD17483F4 , CSD87502Q2 Tool/software: Hi Team, My application includes a CAN interface, which requires GPIO control for enabling and disabling the 120ohm CAN termination…
    • Resolved

  • DRV3245Q-Q1: DRV3245Q-Q1 vs. DRV8353F

    TI Thinks Resolved
    Part Number: DRV3245Q-Q1 Other Parts Discussed in Thread: DRV8353F , DRV8162 , CSD , CSD18514Q5A , CSD18543Q3A , CSD88539ND , CSD87502Q2 Tool/software: Hi.. One of my customer is looking for the motor driver solution for 24V/5A BLDC. They are considering…
    • Answered

  • RE: MOSFET

    Resolved
    Hello Yamaguchi san, Thanks for promoting TI FETs at your customer. Our closest cross to the Toshiba device is the CSD87502Q2. This is a 30V, dual NFET in 2x2mm SON package. TI doesn't make more than 2 FETs in a single package and we do not have any…
    • Answered

  • RE: TLV1805-Q1: Drive an electromagnetic break

    Resolved
    Hi Paul, thank you again for your reply. I was thinking in switch the coil voltage with a MOSFET. It's a good idea what you suggest, that way I would know if the switch is close before actuating the coil, then can I use the MOSFET to actuate it? …
    • Answered

  • RE: TIDA-00540: Multiprotocol Transceiver Reference Design with THVD15xx

    Resolved
    Hi Ben, You can find a detailed description of the operation of this circuit here: www.ti.com/.../TIDA-01238 Basically, a dual FET (CSD87502Q2) is used to enable the 120-Ohm termination when the FETs are on and disable it when the FETs are off…
    • Answered

  • RE: Match MOSFET gate driver to MOSFET

    Resolved
    Hello Tina, It would probably help to start with the desired MOSFET and then select a gate driver to match. When looking for a gate driver check the biggest factors: - Switching frequency requirements: At least 3MHz - Supply level: at least 12V…

  • Schematics for TI Review

    TI Thinks Resolved
    Part Number: TPS25730 Tool/software: Hi Team, We are designing a power delivery system with TPS25730D PD Controller. Our requirements are as follows. Kindly review our design attached below and provide your feedback. 3056.usb_pd_ti.pdf

Didn't find what you are looking for? Post a new question.