Search tips
Showing 2,868 results View by: Thread Post Sort by
    Answered

  • BQ24192: USB-to-GPIO interface adapter needed for EVM?

    Resolved
    Part Number: BQ24192 Other Parts Discussed in Thread: USB-TO-GPIO , Good morning team, I have a question about the BQ24192EVM-021 board. My customer is trying to read/write to the registers via the USB-mini port, but it doesn't seem to recognize the device…
    • Resolved
    • Answered

  • RE: LM10: Differential amplifier followed by 2X gain amplifier

    Resolved
    Walter, These EVM adapter boards make it easy to test smaller packages on 0.1" based breadboards. https://www.ti.com/product/DIP-ADAPTER-EVM/part-details/DIP-ADAPTER-EVM
    • Answered

  • MMWCAS-RF-EVM: DIP Switch settings for MMWCAS-RF-EVM mounted on MMWCAS-DSP-EVM for booting with CCS

    Resolved
    Part Number: MMWCAS-RF-EVM Other Parts Discussed in Thread: MMWCAS-DSP-EVM Greetings, I'm trying to use processor SDK to use the continuous streaming use case on the setup mentioned in the title. I'm following the boot from CCS, however, I don't see a…
    • Resolved
    • Answered

  • RE: PGA460PSM-EVM: Energia code library guides adaptation to ESP32 in Arduino IDE

    Resolved
    Hi Gabriel , When you attempted to capture the echo data dump, did you ensure the DATADUMP_EN in the EE_CNTRL register bit was set to '1'? By default, this value always starts-up as '0' which prevents the echo data dump results from updating. Only either…
    • Answered

  • Different USB Interface Adapter EVM response time

    Resolved
    Other Parts Discussed in Thread: USB-TO-GPIO Hi Expert, The customer purchased many TI USB Interface Adapter for factory firmware programing needed . But they found the response time is different from brought from 2017 and brought from 2019. The customer…
    • Resolved

  • TPA6304-Q1: Does the USB-to-I2C adapter and More Recent EVM GUI Work with TPA6304?

    TI Thinks Resolved
    Part Number: TPA6304-Q1 Other Parts Discussed in Thread: TAS5414 Gregg, I think Adam Daluga (TI's customer-facing engineer for Indiana) and my boss have completed exchange of TI's NDA to cover this. I am in possession of a long form data sheet…

  • RE: CCS/TDA2HV: The 20pin--mipi adapter of XDS200 emulator when use J6 EVM board

    Hello, You should have an adaptor either in the JTAG or EVM box. In any case, here is an exhaustive list of supported JTAG adapters. In some cases, you may need a couple of nested converters. On the bottom of the page, there are links pointing to where…
    • Answered

  • FMC-ADC-ADAPTER: Connecting the ADS52J90EVM to a Xilinx EVM

    Resolved
    Part Number: FMC-ADC-ADAPTER Other Parts Discussed in Thread: ADS52J90EVM , ADS52J90 , , AFE58JD18 Hi, I'm working on a motor control project where we need to simultaneously sample 36 current measurement channels plus an additional couple of measurements…
    • Resolved
    • Answered

  • DRV8886EVM: How to Adapt This EVM for Different Interface Application

    Resolved
    Part Number: DRV8886EVM Other Parts Discussed in Thread: DRV8886 , DRV8880 , LM317 Hi , I am trying to adapt this DRV8886EVM for stepper motor application with such interface as below, 36V for VM. 5V signal on/off for enable /disable of motor rotating…
    • Resolved

  • RE: DUAL-DIYAMP-EVM: Which package can be assembled to DUAL-DIYAMP-EVM?

    Hello Kazuya, Kazuya Nakai59 said: Q1. Can VSSOP8pin package be assembled to the EVM? No, the DUAL-DIYAMP-EVM is only compatible with SOIC-8 package amplifiers. I recommend the customer sample TLV9052 in SOIC-8 package for the EVM, and design with VSSOP…

Didn't find what you are looking for? Post a new question.