• DRV2510Q1EVM: Where could I download the firmware for DRV2510-EVM

  

  ?? ?

  TI Thinks Resolved

  Part Number: DRV2510Q1EVM Dear TI Where could I download the firmware for DRV2510-EVM? I need to compile it in CCS. BR Johnson

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum

• DRV2510-Q1: Where could I get the DRV2510Q1EVM firmware?

  

  ?? ?

  TI Thinks Resolved

  Part Number: DRV2510-Q1 Other Parts Discussed in Thread: DRV2510Q1EVM , MSP430G2553 , DRV2605 Hi TI support Where could I get the DRV2510Q1EVM firmware? And I assume it could run in CCS. BR Johnson

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum

• DRV2510Q1EVM: DRV2510Q1EVM

  

  Avi Alfasi

  TI Thinks Resolved

  Part Number: DRV2510Q1EVM Hi, I would like to use DRV2510 driver for one coil motor. The input signal including a DC, That means the during a 1 cycle of work there is time that the input is just a dc voltage. Is this drive can drive a dc signal? is the…

  • over 2 years ago
  • Motor drivers
  • Motor drivers forum

• DRV2510Q1EVM: Driver disabling after waveform playback

  

  Michael Drummond

  TI Thinks Resolved

  Part Number: DRV2510Q1EVM I'm using the haptics control console with the DRV2510Q1. I get the expected result with the actuator when I'm in the Standard Drive tab in HCC. However, when I switch to the WaveBuilder and play a waveform, the waveform plays…

  • over 1 year ago
  • Motor drivers
  • Motor drivers forum

• DRV2510Q1EVM: DRV2510Q1EVM

  

  hui yuan

  TI Thinks Resolved

  Part Number: DRV2510Q1EVM how to adjust the frequency and amplitude of the sine wave? and how the pwm frequency impact to output?

  • over 3 years ago
  • Motor drivers
  • Motor drivers forum

• DRV2510Q1EVM: about application of 2510

  

  hui yuan

  TI Thinks Resolved

  Part Number: DRV2510Q1EVM Other Parts Discussed in Thread: DRV2510-Q1 Hi Some question about 2510: 1 datasheet show single ended source application how to realize the self bias , if the output is like below shown(have is positive ,half is negetive), how…

  • over 2 years ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV2510Q1EVM: DRV2510EVM resistor function check

  

  Marc Liu

  Resolved

  Part Number: DRV2510Q1EVM Hi Team, For page 10 of https://www.ti.com/lit/ug/slou449/slou449.pdf , there are two resistors R6/R11 after two stages RC filters. What's the use of these two resistors and how to choose the value. Thank you! Marc

  • Resolved

  • over 3 years ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV2510Q1EVM: Could we generate sin wave in DRV2510-Q1EVM

  

  Marc Liu

  Resolved

  Part Number: DRV2510Q1EVM Other Parts Discussed in Thread: DRV2510-Q1 Hi Team, For DRV2510-Q1 EVM, could we generate sin wave from MPS430 and how to realize it? If the input of DRV2510-Q1 is sin wave, the output should still be square wave, right? Thank…

  • Resolved

  • over 3 years ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV2510Q1EVM: How to use DRV2510-Q1 EVM to generate negative output?

  

  Marc Liu

  Resolved

  Part Number: DRV2510Q1EVM Other Parts Discussed in Thread: DRV2510-Q1 Hi Team, May I use DRV2510-Q1 EVM to generate negative output? Could you help provide an example of setting or waveBulider example in Console? Thank you so much! Marc

  • Resolved

  • over 3 years ago
  • Motor drivers
  • Motor drivers forum
Answered

• DRV2510Q1EVM: DRV2510Q1EVM

  

  Nicolas Roch

  Resolved

  Part Number: DRV2510Q1EVM Hi! I'm using the DRV2510Q1 EVM to drive an electromagnet with a PWM on IN+ and a 3.3V level on IN- generated by an extern microcontroller. I read the register with the Haptics Control Console. The DRV2510Q1 turn in fault…

  • Resolved

  • over 5 years ago
  • Motor drivers
  • Motor drivers forum

Didn't find what you are looking for? Post a new question.