• 

  Daisuke Higa

  • 3 months ago
  • Sensors
  • Sensors forum

  DRV5032: Where is the online design tool for DRV5032?

  • Resolved

  Part Number: DRV5032 Hi support team！ I can't find the online tool in datasheet for DRV5032 below
• 

  Julio Apps

  • 2 months ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: WEBENCH® Tools/DRV5032: How to calculate from Flux to Tesla

  Hi Nonthaphat, Thanks for reaching out, Tesla = Webers/area as you outlined above. Im not sure how your equipment relationship from voltage to webers and area of the coil works so i will only comment on the Tesla conversion. Maybe reference the Manual...
• 

  Ian Wang

  • 3 months ago
  • Sensors
  • Sensors forum

  DRV5032: DRV5032 Application Issue

  TI Thinks Resolved

  Part Number: DRV5032 Hi Sir, Customer using DRV5032 found sensor issue, some devices cannot detect success. We check ID tolerance looks fine, guess if possible cause by Bop higher. Would you pls kindly advise? Hall element (mT) close ...
• 

  Ian Wang

  • 6 months ago
  • Sensors
  • Sensors forum

  DRV5032: DRV5032

  TI Thinks Resolved

  Part Number: DRV5032 Hi Sir, Would you pls help for questions about DRV5032? Thanks. 1. Omnipolar: if it means always has output, no matter S or N closer DRV5032? 2. There is no output of DRV5032 when magnet close, can I say “Hall Sensor no work...
• 

  Yumiko hayashi

  • 6 months ago
  • Sensors
  • Sensors forum

  DRV5032: Product recommended

  • Resolved

  Part Number: DRV5032 Hi sir, Can you give me some Suggestion on product selection? Requirement
• 

  Scott Bryson

  • 5 months ago
  • Sensors
  • Sensors forum

  RE: DRV5032: trigger range of unipolar functionality

  Andrew, For each device there will be a specific threshold which will trigger Bop and likewise for Brp. Assuming a known ideal field, this exact threshold can vary from device to device.While most devices will operate near the typical value, it's...
• 

  Scott Bryson

  • 5 months ago
  • Sensors
  • Sensors forum

  RE: DRV5032: What meaning have shown in magnetic response curve of sensor if B is either of more than BOP or less than BRP?

  Andrew, Thank you for your question. Each output only responds to a specific magnetic field polarity. So in either case, the key regions of interest are immediately surrounding Bop and Brp. Your understanding of the behavior of OUT2 is correct. For...
• 

  CARLOS V

  • 6 months ago
  • Sensors
  • Sensors forum

  DRV5032: FD Can be used to create a quadrature output for speed sensors?

  TI Thinks Resolved

  Part Number: DRV5032 I am looking for a Hall-effect IC switch that will be used in a back-application (I guess this IC switch must be unipolar to be used with a permanent magnet and a ferrous gear) that has two square outputs shifted 90° in order...
• 

  SHH

  • 6 months ago
  • Sensors
  • Sensors forum

  DRV5032: Asking for the design on DRV5032 simulation

  TI Thinks Resolved

  Part Number: DRV5032 Hi Team, Customer is designing DRV5032 and request simulation. I provide the DRV5032 calculator tool. To customer. However, customer feedback the tool is too simple. Would you please provide the external third party or other...
• 

  Ian Wang

  • 9 months ago
  • Sensors
  • Sensors forum

  DRV5032: DRV5032

  TI Thinks Resolved

  Part Number: DRV5032 Hi Sir, Would you pls kindly help customer's question about DRV5032? Thanks.

Didn't find what you are looking for? Post a new question.

• Ask a new question