Search tips
Showing 14 results View by: Thread Post Sort by
    Answered

  • DRV8215: Factory settings of drv8215

    Resolved
    Part Number: DRV8215 Tool/software: Hello, I want to use PWM to drive drv8215, but it has two modes: PWM and I2C. I want to know which one is its factory setting.
    • Resolved

  • DRV8215: full management by I2C

    TI Thinks Resolved
    Part Number: DRV8215 Other Parts Discussed in Thread: DRV8830 Tool/software: Hello, could this part be managed just using i2c? No PWM/EN/PH connections. I'm thinking of a replacement for DRV8830. Regards.

  • DRV8215: tTURNOFF for nSLEEP

    Part Number: DRV8215 Tool/software: Team, DRV8215 datasheet mentions on page 33: 7.4.2 Low-Power Sleep Mode When the nSLEEP pin is low for tTURNOFF time, the DRV8215 enters a low-power sleep mode. In sleep mode, the outputs remain High-Z and the device…

  • DRV8215: Datasheet error tINRUSH description

    TI Thinks Resolved
    Part Number: DRV8215 Tool/software: Team, looks like datasheet of DRV8215 contails mismatching information on page 22: When voltage or speed soft-start is disabled, the tINRUSH time directly reflects the setting of the TINRUSH bits. The tINRUSH…

  • DRV8215: Datasheet error Table 7-1

    TI Thinks Resolved
    Part Number: DRV8215 Tool/software: I think there is an error in table 7-1, since the mentioned pull-up resistors usually are connected to Vcc and NOT to VM, right?

  • DRV8215: Brushed DC Motor Driver

    TI Thinks Resolved
    Part Number: DRV8215 Other Parts Discussed in Thread: DRV8837 Tool/software: Hello, I am looking for an IC to control a 3V Brushed DC motor, maximum current in stall is about 100mA. The motor should have current control on the motor, being able…
    • Answered

  • DRV8215: Over current protection is triggered instantly - even at 1% PWM on my 13 ohm motor

    Resolved
    Part Number: DRV8215 Tool/software: Hi all, I'm using the EVAL board (DRV8215EVM) for the DRV8215. I follow the steps on the GUI and go to the Driver Control Panel. These are the settings: - Set H-Bridge control to PH/EN - Fixed off-time current…
    • Resolved

  • DRV8215: Motor driver for a DC brushed motor

    Part Number: DRV8215 Other Parts Discussed in Thread: DRV8213 , , DRV8214 Tool/software: Hello, I am interested in using one of your DRV821X series components. Mainly, I am interested in the DRV8213 and DRV82135 because of the features they offer. …

  • TPS61378-Q1: Looking for the best Boost Controller for my application

    Part Number: TPS61378-Q1 Other Parts Discussed in Thread: DRV8235 , TPS61376 , DRV8215 Hi, I'm going to have to boost 4 series alkaline batteries up to 12VDC at 1.2A max. So roughly 4V to 6V input voltage. The 12V output will be used to drive a brushed…

  • DRV8215EVM: Motor sensing design

    Part Number: DRV8215EVM Other Parts Discussed in Thread: DRV8212 , DRV8213 , DRV8215 , DRV8214 Tool/software: Hello, I am interested in using one of your DRV821X series components. Mainly, I am interested in the Evaluation Boards of the DRV8212, DRV8213…

Didn't find what you are looking for? Post a new question.