TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 222 results View by: Thread Post Sort by
    Answered
  • DRV8876: DRV8876

    siva periasamy
    siva periasamy
    Resolved
    Part Number: DRV8876 Tool/software: Hi Do have the Berkley 3F5 SPICE model for DRV 8876? I hope to simulate an application using DRV8876 in Proteus Thanks Siva
    • Resolved
    • 3 months ago
    • Motor drivers
    • Motor drivers forum
  • DRV8876-Q1: output current control

    Josh Wei
    Josh Wei
    TI Thinks Resolved
    Part Number: DRV8876-Q1 Tool/software: Hi team, I have below two questions for DRV8876QPWPRQ1: If this BDC driver is used for driving the relay coil, could it control the current? For example, start at 3.5A and maintain at 2A. Could this current be…
    • 1 month ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8876: Multi-Channel H-Bridge Driver

    Glen Johnson
    Glen Johnson
    Resolved
    Part Number: DRV8876 Other Parts Discussed in Thread: DRV8906-Q1 , DRV8847 , , UCC27624 Tool/software: Hi, I am looking for a 4 to 8 (6 is preferred) channel half bridge driver. Each output channel is controlled by a logic input. The chip needs a built…
    • Resolved
    • 2 months ago
    • Motor drivers
    • Motor drivers forum
  • DRV8876-Q1: How to choose R_PMODE?

    zouyongchang
    zouyongchang
    TI Thinks Resolved
    Part Number: DRV8876-Q1 Tool/software: hello team: I have a question as follows: In DRV8876-Q1 'S specification,there is some recommended external components for the device,and the R_PMODE is in one of them. However,when an turn to Section…
    • 2 months ago
    • Motor drivers
    • Motor drivers forum
  • DRV8876-Q1: how to configure the PMODE high-impedance mode mentioned in the datasheet?

    Harry Ma
    Harry Ma
    TI Thinks Resolved
    Part Number: DRV8876-Q1 Other Parts Discussed in Thread: DRV8876 Tool/software: HI Team The attached file is about the DRV8876 chip. how to configure the PMODE high-impedance mode mentioned in the datasheet?
    • 1 month ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8876-Q1: Output transient protections

    Jessica Riley
    Jessica Riley
    Resolved
    Part Number: DRV8876-Q1 Tool/software: Are there any recommendations for protections on the outputs of the DRV8876-Q1 device? TVS to clamp voltage transients? Diode to clamp negative voltage swings? I am using the driver in independent PWM output control…
    • Resolved
    • 3 months ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8876-Q1: Current limit when operating in Independent Half-Bridge mode

    Jessica Riley
    Jessica Riley
    Resolved
    Part Number: DRV8876-Q1 Other Parts Discussed in Thread: DRV8703-Q1 Tool/software: Is it possible to set the current limit while operating in Independent Half-Bridge mode (PMODE = open)? Section 7.3.2.3 says that internal current regulation is disabled…
    • Resolved
    • 4 months ago
    • Motor drivers
    • Motor drivers forum
  • DRV8876-Q1: Software Selectable IMODE

    Egemen Aksoy
    Egemen Aksoy
    TI Thinks Resolved
    Part Number: DRV8876-Q1 Tool/software: Hello, In our design, we are using DRV8876-Q1. For the IMODE selection, IMODE selection resistors are attached. We are using 20.5k instead of 20k and we shall use 52.3k+10k instead of 62k resistor. Is it okay for…
    • 6 months ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8876: Does Parallel capacitor required to drive the simple DC motor using DRV8876

    Murali C
    Murali C
    Resolved
    Part Number: DRV8876 Other Parts Discussed in Thread: DRV8231A , Tool/software: Hi Team, I'm using DRV8876PWPR driver IC to drive the 6v DC motor and operated by 8.4 to 6V (2S1P) battery. Using datasheet, I have implemented the below schematics as my design…
    • Resolved
    • 10 months ago
    • Motor drivers
    • Motor drivers forum
  • Answered
  • DRV8876: brake vs coast mode - recommendation

    KKF
    KKF
    Resolved
    Part Number: DRV8876 Tool/software: Hi, I have an application using DRV8876 in PH/EN Control Mode to drive a DC brushed motor with up to 100mA motor current. PH/EN doesn't allow coast mode. Now I have seen in this e2e post ( https://e2e.ti.com/support…
    • Resolved
    • 8 months ago
    • Motor drivers
    • Motor drivers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question