• Unable to run EnergyTrace standalone

  

  Vivek Bhageria

  TI Thinks Resolved

  Other Parts Discussed in Thread: ENERGYTRACE , LP-CC2652R7 Hi I am trying to run EnergyTrace in standalone mode. Unfortunately, EnergyTrace only runs when the debugger is running. I just get this window if I start EnergyTrace without starting the debugger…

  • 1 month ago
  • Code Composer Studio™︎
  • Code Composer Studio forum

• LP-CC2652R7: Energytrace

  

  Sebastian Fischer

  Part Number: LP-CC2652R7 Other Parts Discussed in Thread: ENERGYTRACE , , CC2652R7 Hi, I'm using the LP-CC2652R7 and energytrace. When will the board be calibrated? Is it once at USB connection? Can I perform a calibration? Best Regards Sebastian

  • 2 months ago
  • Bluetooth®︎
  • Bluetooth forum

• LP-CC2652R7: Energytrace

  

  Sebastian Fischer

  TI Thinks Resolved

  Part Number: LP-CC2652R7 Other Parts Discussed in Thread: ENERGYTRACE Hi, I want to use two Launchpads in parallel. If i try to start a current measurement in CLI with stune the measurement will be interrupted and I got the message "BAD DATA detected"…

  • 3 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• LAUNCHXL-CC26X2R1: LAUNCHXL-CC26X2R1: EnergyTrace

  

  Sebastian Fischer

  TI Thinks Resolved

  Part Number: LAUNCHXL-CC26X2R1 Other Parts Discussed in Thread: ENERGYTRACE Hello, I'm using the LAUNCHXL-CC26x2R1 and want to use Energy Trace via command line tool stune. I already able to measure currents. Now I have one question is it also possible…

  • 3 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• LP-XDS110ET: Use EnergyTrace on a non-TI board?

  

  emc_vish

  TI Thinks Resolved

  Part Number: LP-XDS110ET Other Parts Discussed in Thread: ENERGYTRACE I have an XDS110ET and I want to use energytrace just as a current sensor for an ESP32 board (powering ESP32 board off the 3.3V output pin on the XDS110ET 20P connector) Is this doable…

  • 3 months ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

• CC2652R7: EnergyTrace and Radio ON/OFF control

  

  Logan Becker

  Part Number: CC2652R7 Other Parts Discussed in Thread: ENERGYTRACE Good day, I am using the CC2652R7 launchpad, and I have a function defined below called "configureSED()" that sets the data poll period for a sleepy end device to every 10 seconds.…

  • 3 months ago
  • Zigbee & Thread
  • Zigbee & Thread forum

• LAUNCHXL-CC26X2R1: EnergyTrace Voltage

  

  Sebastian Fischer

  TI Thinks Resolved

  Part Number: LAUNCHXL-CC26X2R1 Other Parts Discussed in Thread: ENERGYTRACE Hello, I'm using the LAUNCHXL-CC26x2R1 and want to use Energy Trace in CCS. The default supply voltage is 3.3V. But I want to change this to 1.8V. I have found several locations…

  • 4 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum

• LAUNCHXL-CC26X2R1: XDS110 EnergyTrace

  

  Sebastian Fischer

  TI Thinks Resolved

  Part Number: LAUNCHXL-CC26X2R1 Other Parts Discussed in Thread: ENERGYTRACE Hello, is it possible to use XDS110 as command line for current measurement?

  • 4 months ago
  • Bluetooth®︎
  • Bluetooth forum
Answered

• ENERGYTRACE: EnergyTrace supports MSP430FG6426?

  

  GR

  Resolved

  Part Number: ENERGYTRACE Hi Be Energy Trace Support MSP430FG6xx device? I can not find in "supported products" in Energy Trace page. But I think MSP430FG6xx series is same userguids to MSP430F6xx. However I can find MSP430F6xx in "supported products…

  • Resolved

  • 7 months ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum
Answered

• Cannot launch EnergyTrace in CCS12

  

  YiKai Chen

  Resolved

  Other Parts Discussed in Thread: ENERGYTRACE When I start EnergyTrace in CCS 12.2.0.00009 , it only show the following dialog box and not start EnergyTrace actually. What can I do to fix this issue?

  • Resolved

  • 5 months ago
  • Code Composer Studio™︎
  • Code Composer Studio forum

Didn't find what you are looking for? Post a new question.