Search tips
Showing 377 results View by: Thread Post Sort by

  • DAC39RF10: Any ways to monitor INA devices on the EVM through the GUI?

    Part Number: DAC39RF10 Other Parts Discussed in Thread: DAC39RF12EVM , Hello, Is there any way that I can use the INA231s (current monitor devices) onboard the DAC39RF10EVM? I couldn’t find the function to monitor these in the DAC39RF12EVM eval software…
    • Answered

  • AFE4300 EVM: DC bias using INA in receive BCM network?

    Resolved
    Other Parts Discussed in Thread: AFE4300 Hey, I was going through the schematic for the evaluation module and noticed that a DC bias (~1.7V) is added to the signals when using the INA (U5). I am assuming that this was done so as to bring the signal…
    • Resolved

  • ZOOMlogic EVM OMAPL138 - power consumption ina 219

    Hello I've got the fallowing problem: - I try to make my system power consumtion measurements. Using cpufreq module I change the cpu speed. "poertop" tells me, that frequency has been actually changed correctly. Unfortunately Difference…

  • RE: INA148: Request for High-Voltage Aging Test Solution for Capacitors (0–200V, 0.01uA–5uA Current Measurement)

    Hi Mingming, Thank you for the additional information. Is there a reason you are looking for a TIA stage versus using the shunt resistor method for low side current sensing? TIAs can measure down to the pA ranges, and the leakage current you need to…
    • Answered

  • TLV3602EVM: TLV3602EVM — Output LOW floor sitting at ~1V on high-Z load instead of near VOL spec (60-80mV)

    Resolved
    Part Number: TLV3602EVM Other Parts Discussed in Thread: TLV3602 Hi, I'm using the TLV3602EVM as the comparator stage in an application, and I'm seeing an output LOW level that is consistently elevated well above the datasheet's specified VOL. I want…
    • Resolved

  • ADC32RF55EVM: Configuration OF ADC32RF55EVM using ADC32RF5xEVM GUI

    Part Number: ADC32RF55EVM Dear TI Team, I am new to using high-speed ADC EVMs and am currently learning how to configure them. We have purchased the ADC32RF55EVM Rev D and are trying to digitize 0–250 MHz IQ signals, with the I signal connected to…
    • Answered

  • INA701: INA701 current sensing larger error than expected

    Resolved
    Part Number: INA701 Other Parts Discussed in Thread: TI-SCB Hi! I'm using the INA701 EVM board (with TI-SCB) to evaluate the INA701 for a customer. I'm testing in the following setup: Lab power supply positive connected to current input of calibrated…
    • Resolved
    • Answered

  • RE: AMC7908: AMC7908 Current Sense Feedback Gate Bias Control and Automation

    Resolved
    Hi Nathan, The AMC7908 uses an INA that requires an external resistor. You can customize the external resistor to any current range, as long as the voltage drop across the resistor meets the datasheet SENSE specs. The device does not have autonomous…

  • DRA821U: DRA821 EVM power consumption measurement

    Part Number: DRA821U Other Parts Discussed in Thread: DRA821 Tool/software: Dear Sir, Is there DRA821 power consumption measurement data for DRA821 EVM? There are INA on EVM for each power rails. Is there a script which customer can use to read…
    • Answered

  • ADC12DJ5200RFEVM: How to change INA/INB port via DLL

    Resolved
    Part Number: ADC12DJ5200RFEVM Tool/software: Hello Community. I am using ADC12DJ5200RFEVM. Basically I use the INA port to input analog signals, but sometimes I want to switch to the INB port. I found that with the ADCxxDJxx00RF EVM GUI, I can switch…
    • Resolved

Didn't find what you are looking for? Post a new question.