Answered

• ISO7760: Device Functional Modes

  

  Kuramochi Tadahiko

  Resolved

  Part Number: ISO7760 Hi, Regarding "Device Functional Modes", there is "Undetermined" condition on OUTPUT as below. Does it mean floating? In this case, Can the output logic state be decided by pull-up/down resistor? Best Regards…

  • Resolved

  • 3 months ago
  • Isolation
  • Isolation forum

• RE: ISO7760-Q1: ISO7760-Q1 spice model request.

  

  Manuel Chavez

  Hi Keerthi, Thank you for posting, and welcome to E2E! Unfortunately, at this time we do not have Spice models of digital isolator devices we can share. Please feel free to evaluate the device using IBIS models as linked above. Thank you, Manuel Chavez

  • 6 months ago
  • Isolation
  • Isolation forum

• ISO7760: schmitt trigger

  

  [FAE] Andrew Wang

  TI Thinks Resolved

  Part Number: ISO7760 Hi Team, Is our ISO77 family integrate schmitt trigger inside? So it could be more immune to noise? Cusotmer is asking, thanks. Thanks! Andrew

  • 4 months ago
  • Isolation
  • Isolation forum

• ISO7760: DC/DC swiching noise interference concerns

  

  Rock Su

  TI Thinks Resolved

  Part Number: ISO7760 Hi, The customer is designing their ISO7760 PCB as below picture: The big red box is an isolated DCDC REM6E-1711074 in top layer, REM6E-1711074 datasheet is in attached. But in bottom layer small red box is ISO7760. This PCB board…

  • 8 months ago
  • Isolation
  • Isolation forum

• ISO7760: high voltage input protection/behavior

  

  TISL

  TI Thinks Resolved

  Part Number: ISO7760 Dear e2e support, My customer needs to protect the ISO7760F inputs from high voltages (up to 90V during several seconds), in case of dysfunctions inside his system/application. So the ISO inputs have been protected by series resistors…

  • 9 months ago
  • Isolation
  • Isolation forum

• ISO7760: iso7760 evb

  

  Alex Chen9

  TI Thinks Resolved

  Part Number: ISO7760 Other Parts Discussed in Thread: ISO7762 , ISO7762DBQEVM , ISO7762DWEVM Hi sir I want to survey the ISO7760 for my new design but I can't find the EVB, do you have any suggestion? thanks

  • over 1 year ago
  • Isolation
  • Isolation forum

• ISO7760: How about the output current when 6-ch are all at normal work

  

  Lucas Ding

  TI Thinks Resolved

  Part Number: ISO7760 Hi team, How about the output current of each channel when working at 5V and 6-ch are all at normal work? In the POWER RATINGS part of the datasheet, it seems the maximum current is about 242mW/5.5V=44mA, but in the ABSOLUTE MAXIMUM…

  • 9 months ago
  • Isolation
  • Isolation forum
Answered

• ISO7760: how to protect output from 4kV surge testing

  

  Chenghu Wang

  Resolved

  Part Number: ISO7760 Other Parts Discussed in Thread: TVS0500 , ISO1212 , ISO1211 Hello, I'm using ISO7760 on an interface card. It is powered by 5V and Its outputs are routed to line connector directly. The line interface is subjected to EN61000-4-5 4kV…

  • Resolved

  • 11 months ago
  • Isolation
  • Isolation forum
Answered

• ISO7760: Question on Power Rail

  

  Mitchell

  Resolved

  Part Number: ISO7760 Hi Team, My customer is using the ISO7760F to isolate signals from an FPGA and signal to analog switch. We’re trying to understand if it’s acceptable to run this part at different Vcc based on each own gnd reference. In the datasheet…

  • Resolved

  • over 1 year ago
  • Isolation
  • Isolation forum
Answered

• ISO7760: Layout for ISO7760

  

  yoshiki hasebe

  Resolved

  Part Number: ISO7760 Dear Sirs, My customer asked us about layout for ISO7760. He is troubled about the layout. He is thinking of placing ISO 7760 on TOP and Bottom to make good use of the pattern. Is it possible to place the same ISO 7760 on the bottom…

  • Resolved

  • over 2 years ago
  • Isolation
  • Isolation forum

Didn't find what you are looking for? Post a new question.