Answered

• LDC1614-Q1: input capacitance

  

  Shinji Tsuji

  Resolved

  Part Number: LDC1614-Q1 Hi team, Could you advice the min/typ/max of input capacitance for the pins below? Pin1 : SCL Pin2 : SDA Pin 9 to 16 : Sensor input (it is specified as typical 4pF. I would like to know min and max) regards,

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• LDC1614-Q1: pull down resistor value

  

  Shinji Tsuji

  Resolved

  Part Number: LDC1614-Q1 Hi team, Could you advise the maximum pull down resistor used for pin4(ADDR) and pin6(SD)? I plan to pull down those pins with 10kohm resistor. Please advise if there is any issue. regards.

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• LDC1614-Q1: Fault detection and recovery

  

  Shinji Tsuji

  Resolved

  Part Number: LDC1614-Q1 Other Parts Discussed in Thread: LDC1614 Hi team, I am investigating LDC1614-Q1's fault(error) detection and recovery functions. So far I could only find following items listed in status register. Does this device have other…

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• LDC1614-Q1: Sensor amplitude violation

  

  Shinji Tsuji

  Resolved

  Part Number: LDC1614-Q1 Hi team, How does LDC1614-Q1 behaves when the oscillation amplitude exceed greater than 1.8V and the internal ESD clamping circuit will become active? - Is there a hardware reliability risk? thermal, excessive current drawn…

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum

• LDC1614-Q1: Multiple Layer Inductor Construction for increasing Rp

  

  Shinji Tsuji

  TI Thinks Resolved

  Part Number: LDC1614-Q1 Other Parts Discussed in Thread: LDC1614 Hi team, I am planning to use multiple layer inductor construction in order to increase Rp value for my LDC1614-Q1 measurement. I read a past e2e thread that this construction intended…

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• LDC1614-Q1: Output Drift

  

  Akihiro Hirata

  Resolved

  Part Number: LDC1614-Q1 Hello Team, I made the touch on metal board using LDC1614-Q1, but found the LDC1614-Q1 output continued to increase gradually. Could you let me know the possible reason and countermeasure against it? Regards, Hirata

  • Resolved

  • over 6 years ago
  • Sensors
  • Sensors forum

• LDC1614-Q1: External Clock Tolerance

  

  Akihiro Hirata

  TI Thinks Resolved

  Part Number: LDC1614-Q1 Other Parts Discussed in Thread: LDC1614EVM Hello team, When external clock is used for the LDC1614-Q1, are there any tolerance recommendation for the external clock tolerance? How to think about this? Regards, Hirata

  • over 6 years ago
  • Sensors
  • Sensors forum

• LDC1614-Q1: Conversion time

  

  Shinji Tsuji

  Part Number: LDC1614-Q1 Other Parts Discussed in Thread: LDC1614 Hi team, I have a question about the conversion time for multi-channel operation mode of LDC1614 for 4channel. CLKIN=40MHz I would like to read out all 4 channel in 48msec cycle. …

  • over 5 years ago
  • Sensors
  • Sensors forum

• RE: LDC1614-Q1: RGH0016A DIM A

  

  Kristin Jones93

  Hello Suzuki-san, My apologies for the delayed reply. I was on vacation all of last week. No, your customer does not have to specify lead thickness when ordering the LDC1614-Q1. Best Regards,

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• LDC1614-Q1: Optimizing the Rp parameter

  

  Shinji Tsuji

  Resolved

  Part Number: LDC1614-Q1 Other Parts Discussed in Thread: LDC1614 Hi team, I am optimizing the resolution of the distance measurement using LDC1614 with 10mm diameter circular coil. I have a question about the parameter Rp. Is there optimal range of…

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum

Didn't find what you are looking for? Post a new question.