TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 121 results View by: Thread Post Sort by
  • LM2776: EN pin Threshold ( VIH ) max.

    Adwait Deshpande
    Adwait Deshpande
    TI Thinks Resolved
    Part Number: LM2776 Tool/software: Hello , I am using the LM2776 to generate a negative supply, and in the Electrical Characteristics section of the datasheet, the minimum enable voltage ( VEN(min) ) is specified as 1.2V , but the maximum VEN is not mentioned…
    • 1 month ago
    • Power management
    • Power management forum
  • Answered
  • LM2776: Internal MOSFET Structure

    R.Fukunaga
    R.Fukunaga
    Resolved
    Part Number: LM2776 Tool/software: Hi all, About internal MOSFET Structure of this device, This device is a DCDC with intergrated FET and uses an internal MOSFET. 1) Is this MOSFET a high-current power MOSFET? 2) Is this MOSFET a vertical structure or…
    • Resolved
    • 2 months ago
    • Power management
    • Power management forum
  • Answered
  • LM2776: How to calculate the input current

    Kaji@PAN
    Kaji@PAN
    Resolved
    Part Number: LM2776 Tool/software: Hello, I would like to ask you about how to calculate the input current for the LM2776. For general converters, the input current can be calculated from the formula Input power x efficiency = output power. For a negative…
    • Resolved
    • 5 months ago
    • Power management
    • Power management forum
  • RE: LM2776: The LM2776DBVT fails to be powered on. Procedure

    Josef Marsmann
    Josef Marsmann
    Hi Ian, If I understand it correctly, it works with a resistance load over the temperature range, correct? So please create a plot with the VIN and VOUT in addition to the output current and zoom in to the power-on transition in more detail with max resolution…
    • 4 months ago
    • Power management
    • Power management forum
  • Answered
  • LM2776: LM2776

    Yehoram har even
    Yehoram har even
    Resolved
    Part Number: LM2776 Tool/software: Good afternoon. i plane to use LM2776DBVR. page 1 (data sheet ) indicate in typical application the chip with pins. look like pin number 1 is Vin and so on. same data sheet page 3 - pin number 1 is Vout. i want to verify…
    • Resolved
    • 9 months ago
    • Power management
    • Power management forum
  • LM2776: Charge pump IC Failure (LM2776DBVR)

    Andy Kim
    Andy Kim
    Part Number: LM2776 Tool/software: The observed failure mode is that after some amount of time in the field (within a few days), the charge pump is no longer able to output -5V and instead outputs 0 to about -1.5V while getting quite hot. The IC is being…
    • 8 months ago
    • Other wireless
    • Other wireless technologies forum
  • Answered
  • LM2776: What is the input voltage for LM2776?

    Alex Bacanu
    Alex Bacanu
    Resolved
    Part Number: LM2776 Other Parts Discussed in Thread: LMP7721 , INA128 Hello evevryone! I have a question that may seem dumb: What is the VIN voltage range for LM2776? When I checked the datasheet I saw that it is between 2.7 and 5.5V, in the typical application…
    • Resolved
    • over 1 year ago
    • Power management
    • Power management forum
  • LM2776: Charge pump inductor less converter

    John B
    John B
    TI Thinks Resolved
    Part Number: LM2776 Hi, I found an article "The forgotten converter". This article is about charge pump converter. https://www.ti.com/lit/wp/slpy005/slpy005.pdf?ts=1711354424273&ref_url=https%253A%252F%252Fwww.google.com%252F According to…
    • over 1 year ago
    • Power management
    • Power management forum
  • LM2776: Input voltage

    KrnB
    KrnB
    TI Thinks Resolved
    Part Number: LM2776 Other Parts Discussed in Thread: TL7660 I am planning to use LM2776 for VInput of 5.8V max. The operating ranges states is only 5.5V. but abs max is 6V. Please can you comment if it is okay. Please can you also confirm that if TL7660…
    • over 1 year ago
    • Power management
    • Power management forum
  • Answered
  • LM2776: Wrong output voltage

    Barney
    Barney
    Resolved
    Part Number: LM2776 I am getting Vout = -0.7V for the LM2776 part with the following conditions: Vin = 5.5V C between pins 5 and 6 = 1 uF Cout = 2.2 uF Any clues what might be happening here? Thanks, John
    • Resolved
    • over 1 year ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question