Search tips
Showing 1,212 results View by: Thread Post Sort by

  • LM337-N: The Output voltage is dropped and not stabilized

    TI Thinks Resolved
    Part Number: LM337-N Other Parts Discussed in Thread: LM337 , LM317 hello, I work with this component in its normal configuration (Figure 1), and according to the resistor ratio, I should be at the output -49Volt. when I work with the regulator…

  • LM337-N: Is there any tips in using LM337 to make it more stable?

    Answer Suggested
    Part Number: LM337-N Other Parts Discussed in Thread: LM337 , LM317 , LM317-N I am using an LM337-N in sot-223 package. The circuit is simple, but I find the output of the circuit is ringing at a frequency about 17kHz. (I am sorry I have put a wrong…

  • LM350-N-MIL: Document Errors

    TI Thinks Resolved
    Part Number: LM350-N-MIL Other Parts Discussed in Thread: LM350-N , , LM350A Hello team. The TI product page says for the LM350-N-MIL device the data sheet applies to both LM350-N and LM350-N-MIL. In the data sheet Absolute Maximum Ratings it’s not…

  • PSPICE-FOR-TI: LM337

    TI Thinks Resolved
    Part Number: PSPICE-FOR-TI Other Parts Discussed in Thread: LM337 , LM337-N Hello, Attached is a PSPICE design that uses an LM337; in this configuration, the component does not function. Thank you for your help. MES40.zip

  • UA723: negative regulation voltage range

    TI Thinks Resolved
    Part Number: UA723 Other Parts Discussed in Thread: TPS723 , TPS7A30 , LM337-N The datasheet for ua723cdr specifies resistor values for -6V as a minimum negative output voltage regulation. Could I calculate resistor values for -5V and use this part for…
    • Answered

  • LM79L: Do you have temperature coefficient information?

    Resolved
    Part Number: LM79L Other Parts Discussed in Thread: LM337 , LM337-N , LM137 Tool/software: Hi team, Our customer is looking for negative output LDO that meet the following requirements: Output Voltage: -0.5 V to -2.5 V (fixed output type) Output…
    • Resolved

  • RE: TUSB1104: SLS Debug

    Hi, 1 lane1 From what I see the trace lengths are as follows: PIN_T31 -> ss_rx_serial_i (3306 mil) PIN_T30 -> ss_rx_serial_i(n)" (3306 mil) PIN_N37 -> ss_tx_serial_o (3050 mil) PIN_N36 -> ss_tx_serial_o(n) (3050 mil) 2 lane2 FPGA PIN PIN_R33…

  • RE: LM111: LM111 Military Qualification Standard

    Hi Harry, It is confusing. That is due to 40 years of changing standards... To make it more fun, there are *two* versions of the LM111. The ex-National Semiconductor devices (LM111-N and the QMLV devices) and the "second source" TI devices. Most…
    • Answered

  • RE: LM317L: LDO Maximum Load Current

    Resolved
    Hi Kevin, If the nominal operating current is 350 mA, you may need to select LDOs with higher current compliance like the LM317 and LM337-N. Unfortunately, they don't have the same footprint as the low current version. For the 5v regulator, you…

  • RE: SN65DP159: data regarding the prudact

    Hi, Please see below for the details, Die Size: 74.8 X 74.8 MILS Die Thickness: 10.5 MILS Mold Compound P/N: SUMITOMO EME-G700LTD For additional detail, please refer to IPC-9701, JEDEC JESD22-A104D as these are the spec TI follows. Thanks…

Didn't find what you are looking for? Post a new question.