• 

  GARETH OU

  • 1 month ago
  • Power management
  • Power management forum

  LM5060: controlling EN with a switch

  • Resolved

  Part Number: LM5060 Hi I have questions to ask When When EN PIN high has output voltage
• 

  Vi Lu1

  • 1 month ago
  • Power management
  • Power management forum

  LM5060: Choosing Ro in a large capacitance load application

  TI Thinks Resolved

  Part Number: LM5060 The datasheet mentions that in the case of a large capacitive load, you might need to add a series resistor to the Out pin. The section is a little confusing to me. They listed 4 scenarios. My application has a large capacitive load...
• 

  Kuan Wei Chen (Kevin Chen)

  • 13 days ago
  • Power management
  • Power management forum

  LM5060: Function Discussion

  Part Number: LM5060 Dear Team, Vin is 12V, EN pin is R1838 plus 3.3V, both are provided by DC source, the following conditions have been tested 1. After 12V on, the EN pin provides 3.3V, but no output 2. When the 12V & EN pin are on at the same...
• 

  CY Yang1

  • 2 months ago
  • Power management
  • Power management forum

  LM5060: UL certification report

  • Resolved

  Part Number: LM5060 Hi We need LM5060 UL certification report and file number, Could you share
• 

  Christophe Niclaes49

  • 2 months ago
  • Power management
  • Power management forum

  LM5060: LM5060 usage in ORing configuration

  • Resolved

  Part Number: LM5060 Hello, I'm using the LM5060 as power-path controller in an application
• 

  Taru Kapoor

  • 2 months ago
  • Power management
  • Power management forum

  LM5060: LM5060 Max Vin rating

  TI Thinks Resolved

  Part Number: LM5060 Team, A customer is using LM5060 as a high side switch, with maximum operating voltage as 55V. However, they have a test for transients that requires the Vin to be 70V for ~40ms, while the device is enabled. The data sheet however...
• 

  Rajkumar Selvavinayagam

  • 16 days ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: WEBENCH® Tools/LM5060: LM5060

  Hi Rakesh, Thanks for your suggestion, When i increase the timer cap, startup is successful, But how do i confirm the SOA of Mosfet for that time. Thanks, Raj
• 

  Howard Zou

  • 4 months ago
  • Power management
  • Power management forum

  LM5060: output voltage negative workaround

  • Resolved

  Part Number: LM5060 Hi, my customer is using LM5060 to drive a high side switch to connect
• 

  Paul Yeh

  • 4 months ago
  • Power management
  • Power management forum

  LM5060: Customer ask lower cost similar solution to replace LM5060MM/NOPB

  TI Thinks Resolved

  Part Number: LM5060 Hi team, Could you suggest suitable alternative solution to replace LM5060MM/NOPB? Thanks
• 

  Rakesh

  • 3 months ago
  • Power management
  • Power management forum

  RE: LM5060: UVLO & Schematic review

  Hi Gareth, 1. which value should I look at for overvoltage and undervoltage protection? Upper or Lower? 1A) The typical values should be used as reference. However, considering batch-to-batch variation, the threshold can change any where between min...

Didn't find what you are looking for? Post a new question.

• Ask a new question