Search tips
Showing 153 results View by: Thread Post Sort by
    Answered

  • LM5170EVM-BIDIR: LM5170EVM-Jumper Settings

    Resolved
    Part Number: LM5170EVM-BIDIR Hi I have a question regarding the EVM: I am confused in Master Enable pins, it says you can do it by supply external voltage of 3.3 V to PIN 5 EN of J17. and also it says by UVLO pin by J31 (1,2). So I am confused what should…

  • LM5170EVM-BIDIR: LM5170-EVM-BIDIR-JPCB LAYOUT_ALTIUM

    TI Thinks Resolved
    Part Number: LM5170EVM-BIDIR Other Parts Discussed in Thread: LM5170-Q1 Hello TI team I need a PCB layout schematic of LM5170-Q1 EVM for better understanding of the connections of the board. Thanks

  • LM5170EVM-BIDIR: LM5170-EVM-BIDIR-DUTY RATIO

    TI Thinks Resolved
    Part Number: LM5170EVM-BIDIR Other Parts Discussed in Thread: LM5170 Hello I have confusion in measuring duty cycle: I need to measure the duty cycle value which I think in board there is no test point. What is the best way to get the duty cycle measurents…
    • Answered

  • LM5170EVM-BIDIR: LM5170-EVM-BIDIR- ISETA SETTINGS

    Resolved
    Part Number: LM5170EVM-BIDIR Hello TI team I have one confusion for ISETA signal, the user guide says that apply an analog voltage between 0 to 1.5V at ISETA pin. So do I need an external supply with DAC or what should I do for that supply? First I want…
    • Resolved

  • LM5170EVM-BIDIR: LM5170-EVM-BIDIR-SENSING CURRENTS AND DUTY CYCLE MEASUREMENT

    TI Thinks Resolved
    Part Number: LM5170EVM-BIDIR Hello I am using LM5170EVM-BIDIR as a BOOST, My system is to provide 24 V at LV port and load of 10 ohm resistor at HV port. I have few complications: 1. I need to measure the duty cycle value which I think in board there…
    • Answered

  • LM5170EVM-BIDIR: LM5170-EVM-BIDIR-EVM BIAS SUPPLY and R4

    Resolved
    Part Number: LM5170EVM-BIDIR Hello I have a confusion regarding startup of EVM board, I am working on boost mode 24/48. I want to run the board first without installing the R4 resistor, so do I be able to start the board with only external 3.3V supply…
    • Resolved

  • LM5170EVM-BIDIR: Schematic

    TI Thinks Resolved
    Part Number: LM5170EVM-BIDIR Hello I have bought EVM LM5170EVM-BIDIR, I am using for three phase boost configuration. I need EVM board schematic. In user guide and date sheet it is not available, Only have inner circuits schematics are available. Than…
    • Answered

  • LM5170EVM-BIDIR: LM5170-Q1- Boost Operation_Load

    Resolved
    Part Number: LM5170EVM-BIDIR Other Parts Discussed in Thread: LM5170 Hello I am using LM5170EVM-BIDIR, My system is to provide 24 V at LV port and load of 10 ohm resistor at HV port. I am using resistor of 10 ohm instead of E-load. Do it will make any…
    • Resolved
    • Answered

  • LM5170EVM-BIDIR: LM5170-Q1-UVLO SETTINGS

    Resolved
    Part Number: LM5170EVM-BIDIR Hello I have a confusion regarding startup of EVM board, I am working on boost mode 24/48. If I installed the R4 = 100kohm, so do I need to connect the external supply to J17 PIN 5 EN? Because as per my understanding R4 resistor…
    • Resolved

  • LM5170EVM-BIDIR: LM5170-Q1: Design calculator

    TI Thinks Resolved
    Part Number: LM5170EVM-BIDIR Other Parts Discussed in Thread: LM5170-Q1 Hello I have ordered two LM5170-Q1 EVMs. I need a design calculator to calculate the different parameters. Thanks

Didn't find what you are looking for? Post a new question.