Search tips
Showing 57 results View by: Thread Post Sort by
    Answered

  • LMR36015-Q1: Vout short to Vin(battery)

    Resolved
    Part Number: LMR36015-Q1 Hi team, My customer want to confirm if this device can survive in Vout(not SW-pin but after LC filter) short to Vin(car battery) situation. This device's FPWM option has negative current limit, so I think it's no problem. Could…
    • Resolved

  • LMR36015-Q1: LMR36015AQRNXRQ1

    TI Thinks Resolved
    Part Number: LMR36015-Q1 Hi, This is Regarding MPN -LMR36015AQRNXRQ1. Can you please provide the data for current (IVCC) corresponding to VCC. See the below snap. Regards, Ajay Sahu

  • LMR36015-Q1: Which PACKAGE OUTLINE "RNX0012B" or "RNX0012C" is corresponding to "LMR36015AQRNXRQ1"

    TI Thinks Resolved
    Part Number: LMR36015-Q1 Hi team, Which PACKAGE OUTLINE "RNX0012 B " or "RNX0012 C " is corresponding to "LMR36015AQRNXRQ1", which is shown in its datasheet? Regards, Ochi
    • Answered

  • LMR36015-Q1: Behavior when bootstrap capacitor is open

    Resolved
    Part Number: LMR36015-Q1 Hello, We are using the LMR36015FSC3-RNXQ1 to generate 3.3V. Our client is requesting us to do measurements with failure injection. Among other, we have to test the open mode failure of the bootstrap capacitor. I have desoldered…
    • Resolved

  • LMR36015-Q1: LMR36015-Q1

    Part Number: LMR36015-Q1 Hey All, We had found one big problem during debugging LMR3605-Q1, as the theory, input voltage should equal to the output voltage, right? but when we rise the input voltage to 16v, output voltage can not be higher. The system…

  • LMR36015-Q1: LMR36015 light load abnormal power requirement

    TI Thinks Resolved
    Part Number: LMR36015-Q1 Other Parts Discussed in Thread: LMR36015 Hi! I'm using a LMR36015FSC3RNXRQ1 in classic circuit configuration Due the shortage of PMIC, we ar try to use a 3V3 regulator with feedback resistors, to obtain a 14Vdc required…

  • LMR36015-Q1: Unable to simulate LMR36015A-Q1 part on Webench using custom designed part

    TI Thinks Resolved
    Part Number: LMR36015-Q1 Hi Team, We are facing issue with TI Webench while doing LMR36015A-Q1 IC Simulation with customized part data. Webench stops to respond after entering custom part parameters and parameters are not updating on screen as well. …
    • Answered

  • LMR36015-Q1: noise - is it possible to add resistance in series with cap between pin12 and pin4?

    Resolved
    Part Number: LMR36015-Q1 Hi, Is it acceptable to place a resistor in series with the capacitor between the Switch node pin 12 and Bootstrap pin 4? If so, up to what value 5 or 10 ohms? There is a little noise from these supplies being picked up on an…
    • Resolved

  • LMR36015-Q1: LMR36015-Q1 Pin FMEA

    TI Thinks Resolved
    Part Number: LMR36015-Q1 Other Parts Discussed in Thread: LMR36015 LMR36015-Q1 Pin FMEA

  • LMR36015-Q1: EN to VIN voltage offset

    TI Thinks Resolved
    Part Number: LMR36015-Q1 Other Parts Discussed in Thread: LMR36015 The datasheet states that the EN voltage "must not exceed the voltage on the VIN pin by more than 0.3V". Would like to confirm this is under all conditions and is not just applicable…

Didn't find what you are looking for? Post a new question.