Search tips
Showing 39 results View by: Thread Post Sort by
    Answered

  • LMZ30606: minimum load

    Resolved
    Part Number: LMZ30606 Other Parts Discussed in Thread: TPSM82866A Hello, does the LMX30606 require a minimum load? For example would adding a 10k or a 1k resistor between VOUT and GND help to keep the regulator stable when the load is very light. Regards…
    • Resolved
    • Answered

  • LMZ30606: output voltage abnormal

    Resolved
    Part Number: LMZ30606 Other Parts Discussed in Thread: TPSM82480 Hi, expert, My customer found there are two steps of LMZ30606's output. Could you please help analysis the reason? Thanks. C1132 and C1138 are DNP. The green curve is output voltage…
    • Resolved
    • Answered

  • LMZ30606: Does this part support pre-biased startup?

    Resolved
    Part Number: LMZ30606 Other Parts Discussed in Thread: LMZ30602 , , TPS82085 Hello, Unfortunately I cannot find anything about pre-biased startup for LMZ30602/4/6. Is this possible for these devices? If not - what is the maximum voltage allowed at the output…
    • Resolved
    • Answered

  • LMZ30606: synchronization issue

    Resolved
    Part Number: LMZ30606 Hello! I want to use LMZ30606 to supply an FPGA and would like to synchronize the LMZ30606 with a signal from a GPIO pin of the same FPGA. I guess that it is possible to connect directly the FPGA's GPIO to RT\CLK pin of the LMZ30606…
    • Resolved

  • LMZ30606: INH control using MAX16051 (Power Sequencer IC)

    Part Number: LMZ30606 Other Parts Discussed in Thread: LMZ30604 , LMZ31710 , UCD9081 , UCD9090A Dear Sir/Madam, I want the opinion on using MAX16051 device to control the INH pins of LMZ30606 (Qty. 1) and LMZ30604 (Qty. 4). Power Tree : Board Input 12VDC…
    • Answered

  • LMZ30606: LMZ30606 with enable capability?

    Resolved
    Part Number: LMZ30606 Other Parts Discussed in Thread: LMZ23610 , TPSM84624 , LMZM33606 , LMZ31707 Hello there, I was wondering if there is an LMZ30606 part with enable capability? If not, is there another part that supplies >6A with enable capability you…
    • Resolved

  • LMZ30606: Maximum output capacitance - Slow start

    TI Thinks Resolved
    Part Number: LMZ30606 What actually limits the maximum "External output capacitance" stated to be 2000uF in the data sheet? Too high output capacitance will draw too much current on start-up and the over-current protection kicks inn. This can…
    • Answered

  • LMZ30606: Power Good Leakage Current

    Resolved
    Part Number: LMZ30606 What is the max leakage current we'll see from the LMZ30606 power good pin?
    • Resolved
    • Answered

  • LMZ30606: Power Good sink current

    Resolved
    Part Number: LMZ30606 In the situation of concern, the power good pin is pulled-up to 3.3V through 20kohms and there is a 0.1uF capacitor connected to ground. The abs max current for the PG pin is 10mA. Is there any chance of damage to the LMZ30606 device…
    • Resolved

  • LMZ30606: LMZ30606 - Switch from RT Mode to CLK Mode， PG Drop

    TI Thinks Resolved
    Part Number: LMZ30606 Hello Team When switch from RT mode to CLK mode, after about 10us, the PG pin will drop. Is it correct?

Didn't find what you are looking for? Post a new question.