Search tips
Showing 35 results View by: Thread Post Sort by

  • MSPM0G3518-Q1: MSPM0G3518-Q1: PIN MAPPING SHEET

    TI Thinks Resolved
    Part Number: MSPM0G3518-Q1 Other Parts Discussed in Thread: SYSCONFIG Hello, I am currently working on an automotive hardware design project using the MSPM0G3518-Q1 MCU (80-pin LQFP-PN package). The device is being used in a CAN/LIN-based control panel…
    • Answered

  • MSPM0G3518: MSPM0G3518: Intermittent ADC Vref monitoring drop

    Resolved
    Part Number: MSPM0G3518 Hello, I am experiencing an intermittent dip in ADC readings when measuring an internal/external Vref channel. Expected Reading: ~1362-1363 dec ( 1.09V equivalent). Observed Error: After 2–3 minutes of runtime, a…
    • Resolved

  • MSPM0G3518: Request for Security Assessment & Side‑Channel Vulnerability Clarification – MSPM0G3518 Hardware AES (CPA)

    TI Thinks Resolved
    Part Number: MSPM0G3518 Other Parts Discussed in Thread: MSPM0G3507 , , MSPM0G3519 Hello TI Security / MSPM0 Team, We are reaching out as part of our ongoing Product Security Incident Response Team (PSIRT) activities to assess a recently disclosed…

  • MSPM0G3518: MSPM0G3518: RSTCAUSE register always reads BOOTEXNRST (12) standalone, but reads correct POR/SW reset when debugger is attached.

    Part Number: MSPM0G3518 Hello team, I am experiencing a behavior where the Reset Cause register is being overwritten depending on whether an iSYSTEM debugger is physically attached to the board. The Issue: When I power-cycle the board or trigger…

  • MSPM0G3518: [MSPM0G3518] DAP Connection Error (Error -6305) on Custom ECU Board

    TI Thinks Resolved
    Part Number: MSPM0G3518 Hello TI Support Team, I am attempting to debug and flash firmware onto an MSPM0G3518 microcontroller which is integrated into a custom ECU. I am using MSPM0G3518 ( VQFN-32_RHB32 ) and the XDS110 USB Debug Probe via Code Composer…

  • MSPM0G3518: I2C Clock Frequency - TPR

    Part Number: MSPM0G3518 Other Parts Discussed in Thread: MSPM0G3519 The TRM says I2C Frequency is calculated with the following formula: I2C_FREQ = I2C_CLK / ((1+TPR) × (SCL_LP + SCL_HP )) The TRM also says in the description of the CTPR/MTPR register…

  • MSPM0G3518: Inquiry regarding LIN Auto Baud Rate Configuration Parameters (MSPM0G351x MCAL)

    TI Thinks Resolved
    Part Number: MSPM0G3518 Hello TI Support Team, I am currently integrating the LIN MCAL driver for the MSPM0G3518 (using AUTOSAR version 4.4.0) and I have a few questions regarding the Auto Baud Rate configuration for a LIN Slave node. I see the LinChannelAutoBaudRate…

  • MSPM0G3518-Q1: IWDT Reset Reason

    Part Number: MSPM0G3518-Q1 Te following is from the syscfg regarding the IWDT peripheral of G3519 MCU :- The Independent Watchdog timer (IWDT) is part of the LFSS IP and is an SoC independent supervisor which monitors code execution and overall hang…

  • MSPM0G3518: Hard Fault when Writing Flash

    Part Number: MSPM0G3518 We work on target "MSPM0G3518". Our flash driver is located in RAM. We try to write data on code flash, starting from sector "90". We erased the area we wish to flash beforehand. We got hard fault interrupt which after debugging…

  • MSPM0G3518: Sample code is in Debug Configuration, Need to change to Release Configuration

    Part Number: MSPM0G3518 Other Parts Discussed in Thread: MSPM0G3519 Hi, Curretly I am using the MSPM0G3518 with XDS-110 debugger, the build configuration was default Debug mode I created the release mode as per the procedure shared in forum but unable…

Didn't find what you are looking for? Post a new question.