Search tips
Showing 50 results View by: Thread Post Sort by

  • MSPM0L1227: Runtime PORT Configuration Change on MSPM0L1227

    Answer Suggested
    Part Number: MSPM0L1227 Hello all, I am using below Model to Diagnose S2B fault on NTC. The GPIO is to be Disabled during Normal Run Mode i.e R3 should be floating. When Diagnostic is enabled the GPIO will pull the R3 to low. GPIO is configured to Standard…

  • MSPM0L1227: Debugging/Flashing Issues

    Part Number: MSPM0L1227 Other Parts Discussed in Thread: UNIFLASH , MSPM0G3507 While debugging our system based on MSPM0L1227 controller we are encountering some strange behavior. Below are steps we followed: first erase MAIN,DATA and NONMAIN(Other…
    • Answered

  • MSPM0L1227-Q1: MSPM0L1227-Q1 SPI interfacing with TLIN1431

    Resolved
    Part Number: MSPM0L1227-Q1 Other Parts Discussed in Thread: MSPM0L1227 Tool/software: Dear team, to meet the ASIL requirements of our project, we need to enable the CRC feature in the TLIN1431, which is configured to communicate with the MSPM0L1227…
    • Resolved

  • MSPM0L1227-Q1: Using HFOSC for RS485 communication

    Part Number: MSPM0L1227-Q1 Hello MSP team, do you recommend using HFOSC for RS485 communication? Or do you think the clock accucary of HFOSC is not good enough and HFXT is recommended? Best regards, Til

  • MSPM0L1227: Acceptable minimum frequency for sysosc

    TI Thinks Resolved
    Part Number: MSPM0L1227 Other Parts Discussed in Thread: MSP430FR5869 Hi, I would like to confirm acceptable minimum frequency for sysosc of MSPM0L1227. As a comparison, there is following spec on datasheet of MSP430FR5869. This shows user can input approx…

  • MSPM0L1227: MSPM0L122x dual bank example

    Part Number: MSPM0L1227 Team, gpio_toggle_output.c I am using CSS 20.3.0, attaching my SYSCFG file and a test code also along with this mail. I wen through some of the Docs available on enabling bank swap and written code as per my understanding.…
    • Answered

  • MSPM0L1227: Meaning of "OPT" in table "Supported Functionality by Operating Mode"

    Resolved
    Part Number: MSPM0L1227 Hi, I'm confusing meaning of "OPT" which is described in "Supported Functionality by Operating Mode" of datasheet. According to section "8.3 Operating Modes " of datasheet, "PD1" is defined as shown below. ""PD1" is always powered…
    • Resolved
    • Answered

  • MSPM0L1227: Open Drain GPIO Output

    Resolved
    Part Number: MSPM0L1227 Tool/software: Hi expert, Is there any way to implement an open-drain I/O? Thank you.
    • Resolved

  • MSPM0L1227-Q1: Unable to select internal VREF monitor channel (A0_28) in SysConfig under “ADC Conversion Memory Configuration

    Part Number: MSPM0L1227-Q1 Other Parts Discussed in Thread: MSPM0L1227 , SYSCONFIG Hello all, I am planning a self‑test on ADC Of MSPM0L1227 using VREF monitor channel (A0_28) . But i am unable to configure the same using SysCfg. The DataSheet says…

  • MSPM0L1227: NMI

    Part Number: MSPM0L1227 Other Parts Discussed in Thread: MSPM0L2228 Tool/software: Hi Sir We are verifying the functionality of the MSPM0L1227, ......\LP_MSPM0L2228\driverlib\flashctl_ecc_error_injection Example program for testing ECC errors can…

Didn't find what you are looking for? Post a new question.