TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 20 results View by: Thread Post Sort by
  • MSPM0L1303: Comparator appears to always be stuck in one state

    Michael Marne
    Michael Marne
    TI Thinks Resolved
    Part Number: MSPM0L1303 Other Parts Discussed in Thread: SYSCONFIG Tool/software: I am trying to configure the comparator to trigger when the positive terminal goes higher than the negative terminal. I want this to generate an interrupt. I have configured…
    • 10 days ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • RE: MSPM0L1303: signal delaying

    HS FAE Germany
    HS FAE Germany
    Hi Dennis, there are two 307KHz signals to control 2 power supplies. The one signal is delay today and therefore produce inefficiency. The two PWM signals should be as syncron as possible. The delay should be around 200ns. My idea is to use the comparator…
    • 8 months ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • Answered
  • MSPM0L1303: missing OPA register in User Manual

    fabio rodella
    fabio rodella
    Resolved
    Part Number: MSPM0L1303 Other Parts Discussed in Thread: MSPM0L1306 Tool/software: Hi everyone, I downloaded the recent User Manual of the MSPM0l1303 uC, revision D (SLAU847D). In the OPA section it says: but in the Registers section I can't find the…
    • Resolved
    • 10 months ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • MSPM0L1303: MSPM0L read back flash in stop0 mode

    fabio rodella
    fabio rodella
    TI Thinks Resolved
    Part Number: MSPM0L1303 Other Parts Discussed in Thread: MSPM0L1306 Hi everyone, I would like to know if there is a way to read the internal flash memory of the MSPM0L1303 after being programmed to run in stop mode 0. I can not debug the device in stop0…
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • Answered
  • MSPM0L1303: error -614

    fabio rodella
    fabio rodella
    Resolved
    Part Number: MSPM0L1303 Other Parts Discussed in Thread: LP-MSPM0L1306 Hi everyone, do you have any information about error -614? I didn't find anything about that in the h ttps://software-dl.ti.com/ccs/esd/documents/ccs_debugging_jtag_connectivity_issues…
    • Resolved
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • RE: MSPM0L1303: how to limit current when wake up avoiding default 32MHz running

    Dennis Lehman
    Dennis Lehman
    Hi Carlo, I'm closing this posting since this topic is now handled by the designers through email.
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • Answered
  • MSPM0L1303: Executing Factory Reset DAP script in Uniflash

    xiao feng
    xiao feng
    Resolved
    Part Number: MSPM0L1303 Other Parts Discussed in Thread: UNIFLASH Hi TI, I have disable SWD in code because i need to repurpose the GPIO. NRST pin still enabled. Whenever i am trying to re-flash the program, i have to first hold nrst of MCU pin low, connect…
    • Resolved
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • MSPM0L1303: Is it possible to program without NRST

    xiao feng
    xiao feng
    TI Thinks Resolved
    Part Number: MSPM0L1303 Other Parts Discussed in Thread: UNIFLASH Hi Ti, I am using XDS110 to program a custom board with MSPM0L1303. Is there a way to program the module with only SWDIO, SWCLK, GND, 3V3 connected? that would make my test jig a lot simpler…
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • MSPM0L1303: OpAmps, Peak-to-peak input noise voltage

    Hielke Bakker
    Hielke Bakker
    TI Thinks Resolved
    Part Number: MSPM0L1303 We are working on designing a sensor solution using the MSPM0L130x. The plan is to utilize the internal OpAmps for the analog circuit. However, we have been unable to locate aparameters in the electrical characteristics of the…
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • RE: MSPM0L1303: best practice when using SWD pin as GPIO yet still keep the debug access.

    xiao feng
    xiao feng
    thank you! i will just use CCS for now
    • over 1 year ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question