Search tips
Showing 36 results View by: Thread Post Sort by

  • OPA344: Operating outside of Max input voltages

    TI Thinks Resolved
    Part Number: OPA344 Tool/software: I am looking through the Datasheet and found a section near the absolute max section saying " Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than 0.5V beyond the supply…
    • Answered

  • OPA344: Degradation of performance characteristics in transition region in unity-gain configuration OPA344 vs. TLV2461

    Resolved
    Part Number: OPA344 Other Parts Discussed in Thread: TLV2461 , , OPA325 Dear all, we are searching for a suitable OP-Amp for a unity-gain-buffer configuration to buffer the high-impedance source voltage signal which needs to be measured by an other…
    • Resolved

  • OPA344: OPA344

    TI Thinks Resolved
    Part Number: OPA344 Other Parts Discussed in Thread: OPA992 , OPA375 , OPA313 Dear TI-san, I am drafting a question about OPA344 at the link below. Please check contents and answer. e2e.ti.com/.../3969698 Thanks, S.Suzuki
    • Answered

  • OPA313: OPA313, OPA344

    Resolved
    Part Number: OPA313 Other Parts Discussed in Thread: OPA344 Dear TI-san, I got OPA313 advice at the links below. https://e2e.ti.com/support/amplifiers-group/amplifiers/f/amplifiers-forum/1072728/opa344-opa344/3976360#3976360 I am in the process…
    • Resolved
    • Answered

  • OPA313: OPA313, OPA344

    Resolved
    Part Number: OPA313 Dear TI-san, I decided to use a microphone"A" with an output impedance of 5.2kΩ and set resistance of the amplifier input to 3.6kΩ. 3.6kΩ is intended to minimize power supply noise of connected laptop computer. After…
    • Resolved
    • Answered

  • OPA344: Do TI has photodiode design wizard?

    Resolved
    Part Number: OPA344 Hi Expert : Analog devices has photodiode design wizard. The link below is the tool website. Photodiode Circuit Design Wizard | Analog Devices I see TI has similar tool before. But I can not find it all. Could you help…
    • Resolved
    • Answered

  • OPA344: Junction to case parameter confirm

    Resolved
    Part Number: OPA344 Other Parts Discussed in Thread: TLV9101 , , TLV376 Hi Team: Please help to provide Junction to case parameter of OPA344NA for RD request , thanks. Regards / Mark
    • Resolved
    • Answered

  • OPA344: What is the cause and what is the solution for this strange conditioner?

    Resolved
    Part Number: OPA344 Other Parts Discussed in Thread: LM2576 Dear All, Please see the bellow schematic: I experimented the above circuit giving a 50 Hz triangular wave with 3.3V peak to peak voltage and 1.65V of offset voltage. The out put is as…
    • Resolved
    • Answered

  • OPA344: What is the cause and what is the solution for this strange conditioner?

    Resolved
    Part Number: OPA344 Other Parts Discussed in Thread: LM2576 Hi Ras, sorry for being late, but I was very busy in my job. There's a mistake in your PCB: The switcher LM2576 and the rest circuitry should not share the same ground plane! Instead, use…
    • Resolved

  • Problem with OPA344 at -40DegC

    I have been experiencing a problem with the output of a OPA344NA OpAmp, with a particular setup when operated at -40DegC. The device is being used as a simple non-inverting amplifier with a gain of 10.53, when operating at -40DegC and the +ve terminal…

Didn't find what you are looking for? Post a new question.